Extron electronic DVI DL 101 user manual Projector mounting, Through-desk mounting the DVI DL

Page 10

Installation and Operation, cont’d

Through-desk mounting the DVI DL

4. Drill four pilot holes, each 3/32" in diameter by 1/4" deep, where you made marks.

5. Using the provided four wood screws, secure the brackets to the mounting surface.

6. Slide the DVI DL up and down in the mounting brackets until the front panel is at the desired height. Tighten the screws that secure the brackets in place.

If the screws are inaccessible to a screwdriver:

a. Mark the location of the brackets relative to the screws. b. Remove the unit from inside the furniture.

c. Tighten the screws.

d. Replace the unit inside the surface (step 4).

Projector mounting

The DVI DL can be mounted on a projector bracket using either of the following optional Extron projector mounting kits:

PMK 300 projector mounting kit (part #70-374-01)

PMK 350 low profile projector mounting kit

(part #70-563-02[black] or part #70-563-03[white])

PMK 300 mounting

Mount the DVI DL to a PMK 300 bracket as follows:

1. If necessary, remove the feet from the bottom of the unit.

2. Mount the receiver to one of the bracket’s three mounting plates using two of the supplied 4-40 x 3/16" screws in opposite (diagonal) corners to secure the device to the bracket. It can be vertically mounted facing either up or down (see the illustration below).

NOn the side mounting plates, the device is typically mounted on the outside of the bracket.

On the front mounting plate, the device is typically mounted on the inside of the bracket.

Side Mounting

Plate

Bracket

Brace

U-Bolt

Extron

DVI DL 101

Equalizer

Power Supply

Extron

PMK 300

Multi-product Projector Mount Kit

Front Mounting

Plate

PMK 300 projector mounting a receiver

3. Strap the power supply to one of the brackets, using the two included tie wraps.

NThe PMK 300 has a hole in the bottom plate that allows the projector pole to be inserted through the center of the plate, rather than outside of the plate). To install the PMK 300 in this configuration, slide the bracket up from the bottom of the pole before the projector is installed on the pole.

2-6

DVI DL 101 • Installation and Operation

DVI DL 101 • Installation and Operation

2-7

Image 10
Contents User’s Manual Dual Length DVI Cable EqualizerPrecautions Extron’s Warranty安全须知 中文 FCC Class a NoticeTable of Contents Table of Contents, cont’d DVI DLIntroduction FeaturesApplication Diagrams About this ManualTwo Introduction, cont’dTabletop use Installation and OperationMounting the DVI DL Rack mountingThrough-furniture mounting Installation and Operation, cont’dUnder-furniture mounting Mounting the DVI DL 101 on a 3.5 deep rack shelfPMK 300 mounting Projector mountingThrough-desk mounting the DVI DL PMK 300 projector mounting a receiverPMK 350 mounting Mounting with the projector pole on the insidePMK 350 projector mounting a DVI DL Front and Back Panel Features and Connections DVI DL front and rear panelsInput cable lengths Signal PinDVI connector pin assignments Dual and single link modesJumpers on the internal board in default outside position Wiring the power connectorEnabling the DDC Buffer AAppendix a Specifications, Parts, and Accessories Specifications DVI DLAccessories Part number Optional AccessoriesIncluded parts Replacement Part number Cables and AdaptersSpecifications, Parts, and Accessories, cont’d

DVI DL 101 specifications

Extron Electronics DVI DL 101 is a state-of-the-art digital video distribution amplifier designed to provide superior performance in professional environments. This powerful device is particularly well-suited for applications requiring high-quality DVI signal distribution, making it an ideal choice for educational institutions, corporate settings, and broadcast studios.

One of the standout features of the DVI DL 101 is its ability to distribute a single DVI-D signal to multiple displays without any loss of quality. With a single input and up to two DVI outputs, this device ensures that all connected displays receive the same high-quality image. The DVI DL 101 supports video resolutions up to 1920x1200 at a refreshing rate of 60 Hz, making it suitable for HD video applications.

The DVI DL 101 utilizes advanced signal processing technologies, including reclocking and equalization. Reclocking helps to regenerate the digital signal to eliminate any potential distortion that may occur over long cable runs. Meanwhile, equalization adjusts the signal strength to compensate for cable length and quality. Together, these technologies enhance the overall integrity of the digital signals, ensuring consistent and reliable performance across all outputs.

In terms of connectivity, the DVI DL 101 features a DVI-D input and two DVI-D outputs, accommodating various cable configurations. Additionally, the device is designed with a compact and durable chassis, making it easy to integrate into various rack-mounted setups or standalone configurations. The front panel includes LED indicators, providing users with real-time status updates on the power and signal presence.

Another characteristic of the DVI DL 101 is its ease of installation and user-friendly operation. With its plug-and-play functionality, users can quickly set up the device without the need for complex programming or configuration. Furthermore, the DVI DL 101 is compatible with a wide range of DVI sources, including computers, projectors, and digital signage systems.

Overall, the Extron DVI DL 101 is an exceptional choice for any professional environment needing reliable and high-quality DVI signal distribution. With its robust set of features, advanced signal processing technologies, and ease of installation, it stands out as a premier solution for enhancing digital video systems.