H9410UD(EN).qx33 03.1.14 9:21 PM Page 18
PLAYBACK FUNCTION
NORMAL PLAYBACK
VCR
1Insert a prerecorded tape. The VCR will turn
on.
¡If the safety tab has been removed, the
VCR will start playback automatically.
2Turn on the TV and set the TV to channel 3.
¡If noise appears, change the RF output channel of the VCR to channel 4 by pressing PLAY for 3 sec- onds during playback. Then select the same channel (CH4) on your TV. (See “RF OUTPUT CHANNEL” on page 13 for the detail.)
3Begin playback by pressing PLAY.
¡Tracking adjustment will be done automatically (Digital Tracking function) when you start playback. To adjust the tracking manually, press SKIP/CH. on the remote or CHANNEL (UP/DOWN) on the VCR.
¡When a tape has reached the end, the VCR will rewind the tape to the beginning, and eject the tape.
4To stop playback, press STOP.
¡If no corresponding symbols appear on the display when you press buttons such as PLAY, RECORD,
Dor E, that means no cassette tape is in the VCR. Please insert a tape.
Counter Reset
¡You can reset the counter by pressing CLEAR/C.RESET on the remote control twice.
STILL/SLOW
You can freeze the picture on TV screen by pressing PAUSE during playback.
¡You can advance the picture one frame at a time by pressing PAUSE during the Still mode.
¡You cannot manually adjust the tracking of a still picture. However, if the picture begins to vibrate ver- tically during the still mode, you can stabilize the picture by pressing CHANNEL (UP/DOWN).
¡If the picture is distorted or rolling vertically, adjust the vertical hold control on your TV, if so equipped.
¡You can watch in the slow motion by pressing SLOW during playback or the still mode.
¡If a noise bar appears on the TV screen, you can reduce it by pressing CHANNEL (UP/DOWN).
¡After the VCR has been in Still/Slow mode for 5 minutes, it will stop automatically to protect the tape and the video head from damage.
¡To return to playback, press PLAY.
AUTO REPEAT PLAYBACK
VCR
This feature allows you to play a tape over and over.
1Select main menu by pressing MENU.
2Select "AUTO REPEAT" by pressing K or L.
3Begin auto repeat playback by pressing B so that ON appears next to "AUTO
REPEAT".
¡If the
¡To cancel the Auto repeat mode, press B at step [3] so that OFF appears next to "AUTO REPEAT".
SEARCH FUNCTIONS
VCR
PICTURE SEARCH
If you want to skip or repeat a scene during playback, press D or E.
¡Press it again and the VCR will now search at super high speed. (in the LP/SLP modes only).
INDEX SEARCH
An index mark will be assigned at the beginning of each recordings you make. You may skip to a specific marked point by following the steps below.
1Press SEARCH MODE so that the Index Search menu appears.
2Enter the number of recordings you wish to
skip by pressing K or L within 30 seconds.
3Press B or { to start index search.
¡If you want to go in the forward direction, press B. ¡If you want to go in the reverse direction, press {. ¡If you want to stop search function, press STOP.
¡After index search, the VCR will play the tape auto- matically.
TIME SEARCH
This feature allows you to go to a specific point on a tape by entering the exact amount of time you wish to skip in order to reach the point.
1Press SEARCH MODE 2 times so that the Time Search menu appears.
2 Enter your desired time to | TIME SEARCH |
skip by pressing K or L | 2 : 50 |
| |
within 30 seconds. |
|
|
|
3Press B or { to start time search.
¡If you want to go in the forward direction, press B. ¡If you want to go in the reverse direction, press {. ¡If you want to stop search function, press STOP.
¡After time search, the VCR will play the tape auto- matically.
– 18 – | EN |
1L25