LG Electronics 60PC1D, 42PC3D owner manual Regulatory Information

Page 2

Warning

Warning

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of suffi- cient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appli- ance.

NOTE TO CABLE/TV INSTALLER:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as prac- tical.

REGULATORY INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

CAUTION:

Do not attempt to modify this product in any way without written authorization from LG Electronics Corporation. Unauthorized modification could void the user’s authority to operate this product.

COMPLIANCE:

The responsible party for this product’s compliance is: LG Electronics U.S.A., Inc.

1000 Sylvan Avenue, Englewood Cliffs, NJ 07632 Phone: 1-800-243-0000 http://www.lgusa.com

2

Image 2
Contents 37LC2D 50PC3D 42LC2D 60PC1D No 38289U0527F dRegulatory Information Safety Instructions For LCD TV Contents IR Codes 53~58 External Control Device SetupReference Accessories Stand Installation for 32LC2D/UDButtons Controls Model Name 42PC3D/3DV, 50PC3D, 60PC1DButton Buttons Service Connection Options Model Name 42PC3D/3DV, 50PC3D, 60PC1DControls Model Name 32/37/42LC2D, 32LC2DU Swivel Stand 42LC2D OnlyConnection Options Model Name 32/37/42LC2D, 32LC2DU Bright + Remote Control Key FunctionsTimer G p.45 Thumbstick Up/Down/Left/Right/ENTERDash VCR/DVD/DVHS/Camcorder ButtonsMute G p.29 EZ PIC G p.35Ensure the eye-bolts or brackets are tightened securely Installing Batteries42PC3D/3DV, 50PC3D 60PC1D 32/37/42LC2D, 32LC2DU Between the wall and the productInstallation 42PC3D/3DV, 50PC3D, 60PC1D32LC2D/U 37/42LC2D How to remove Cable ManagementMent, see the External equip Ment Connections section How to arrange the cable For 50PC3D How to use stand For 42PC3D/3DVWhen closing the stand for storage Analog and DTV signals provided on two separate antennas Analog and Digital TV signals provided on antennaAnalog and Digital TV signals provided on cable External Equipment ConnectionsWhen connecting with a RCA cable VCR SetupWhen connecting with an antenna External AV Source Setup When connecting with an S-Video cableWhen connecting with a Hdmi cable DVD SetupWhen connecting with a S-Video cable When connecting with a component cable Component Input portsHdstb Setup When connecting with a Hdmi to DVI cable AV Out Setup Digital Audio OutputPC Setup When connecting with a D-sub 15 pin cableHorizontal Frequency kHz Frequency HzScreen Setup for PC mode Adjustment for screen Resolution, Position, Size, and PhaseOn Screen Menus Language Selection Volume AdjustmentBasic operation Turning on the TVOn Screen Menus Selection and Adjustment How to adjust the OSD screenManual Scan Setup Menu OptionsEZ Scan Channel Search Ber Channel EditBers and a preview picture Being received DTV Signal StrengthInput Source TV, AV1, AV2, Component1, Component2, RGB-PC, HDMI1/DVI, orPress the F / G button to select the label Input LabelComponent1-2, RGB-PC, HDMI1/DVI or HDMI2 Auto Picture Control EZ Picture Color Temperature ControlVideo Menu Options Manual Color Temperature Control Selecting the Manual MenuPress the G button and then use D / E button to select XD Press the G Button and then use D / E button to select Advanced-Cinema 32 Mode / Black LevelCinema 32 Mode Black levelVideo Reset Spanish, or French Audio Menu OptionsAudio Language Adjustments Manual Sound Control EZ Sound-UseroptionSelecting the Front Surround SRS TruSurround XTTV Speakers On/Off Setup BalanceTime Menu Options Manual Clock SetupAuto Clock Setup Press the G button and then use D / E button to select OnTo cancel On/Off Timer function, select Off Sleep TimerOn/Off Timer Setup For only On Timer functionTime Menu Options Auto OffOption Menu Features Aspect Ratio ControlCaption/Text Tion languages English, Spanish, or FrenchLow Power 42PC3D/3DV, 50PC3D, 60PC1D only Caption OptionWhite Wash removes permanent images from the screen OrbiterLock Menu Options Parental Lock Setup For USAExternal Control Device Setup Wire ConfigurationsTransmission / Receiving Protocol Command Reference ListSet ID Aspect Ratio Command2c Main picture format Power Command2aInput Select Command2b Main Picture Input Screen Mute Command2dTint Command2j Color Command2iRemote Control Lock Mode Command2m Sharpness Command2kTune Command Command m a ISM Method Command2pLow Power Command2q Input selectCommand x b Main Picture Input Channel Add/Del Command m bKey Command m c IR Codes How to ConnectRemote Control IR Codes Code Hexa Function Programming a code into a remote mode Programming the RemoteCable Box Programming CodesVCRs Digital Cable/Satellite Box AudioTroubleshooting Checklist No output from one Picture OKNo sound Speakers Unusual soundDimensions With stand 44.4 x 29.5x 15.0 inches Dimensions With stand 60.8 x 40.8 x 16.0 inchesWeight With stand Dimensions With stand 51.3 x 34.3 x 14.0 inchesDimensions With stand 41.5 x 32.0 x 11.9 inches Dimensions With stand 31.9 x 24.8 x 9.3 inches32LC2D-UE 32LC2DU-UE Weight With stand 811 x 630 x 235 mm
Related manuals
Manual 69 pages 51.94 Kb