LG Electronics 55LS675H, 42LT670H, 37LT670H, 32LT670H LT2002 Cloning Notes, LT2002 Clone Programmer

Clone Programmer Cloning Procedures (Cont.)

Learning / Teaching a Master TV Setup using an LT2002 Clone Programmer

Caution: If the TV is in LodgeNet PPV Mode (check with the site administrator if you are not certain), do not connect a clone programmer to the GAME CONTROL/MPI port, as this will damage the clone programmer.

Cloning is accomplished using the TV/clone programmer MPI ports for communication (see figure).

LT2002 Cloning Notes

• Read the IMPORTANT CLONING

INFORMATION on page 28 before

beginning any cloning procedures.

• A slow flashing green light indicates

that there are communication

Antenna

or CATV

MPI

Cable

	problems between the TV and the
	LT2002. If this is the case, check for
	a damaged cable, poor contacts, or
	other connection troubles.
•	If the status indicator is red, the
	LT2002 batteries are low and should
	be replaced. Install four (4) high-
	quality alkaline AA batteries.
•	Learning and Teaching is only
	possible between identical model TVs;
	however, the LT2002 can store up to
	three different Master TV Setups.

Learn Setup from Master TV

THE CLONE HAS CONTROL OF THE TV

THE CLONE IS VERSION XX

THE TV IS VERSION		XX
THE SW IS REVISION		XX
CLONE CLOCK = XX:XX
TV	CLOCK = XX:XX

-PRESS ANY KEY TO CONTINUE.

-DISCONNECT CLONE WHEN DONE.

Ferrite Core (TDK, ZCAT 2035-0930)

LT2002 Clone Programmer

Connect cable to
TV MPI Jack and		Status
follow on screen
instructions		Indicator
	MPI
				Reset
			Color
	• green		battery ok
	• red		battery low
		Blink pattern
	• slow		power on

no communications

• heartbeat power on communications ok

QuickSet II Programmer

LT2002

ZENITH ELECTRONICS CORPORATION, LINCOLNSHIRE, ILLINOIS, USA

1.Ensure the Master TV is set up completely and in Pass-through Mode.

2.Tune/set the TV to an analog channel or Aux input, and then plug one end of the MPI cable into the TV MPI port.

3.If there is a good connection after the LT2002 is connected to the TV MPI port, “THE CLONE HAS CONTROL OF THE TV” message will appear on the TV screen. Press any key on the Installer Remote to access the LT2002 Clone Selection Menu.

4.Press 1 on the Installer Remote to select LEARN FROM TV from the Clone Selection Menu; then press OK to proceed to the Memory Bank Selection Menu.

5.Press 1, 2, or 3 on the Installer Remote to select the clone Memory Bank in which to store the Master Setup. Then, press OK.

CLONE SELECTION MENU

(1) LEARN FROM TV

(2)TEACH TO TV

(3)SET CLONE CLOCK FROM TV

(4)SET TV CLOCK FROM CLONE

(5)DISPLAY TV SETUP

(6)DISPLAY CLONE SETUP

-TO CHANGE MENU ITEMS, PRESS CHANNEL KEYS OR DIGITS.

-TO EXECUTE ITEM, PRESS ON/OFF, POWER, OR ENTER.

SAVE TV SETUP IN SELECTED

CLONE MEMORY

Note: If you choose a Memory Bank that already has a Master device’s setup programmed into it, that setup will be overwritten by the new Master TV Setup.

6.Verify the Learning setup information on the next screen, and then press POWER to transfer the Master TV Setup into the selected Memory Bank on the LT2002.

Learning usually takes about 90 seconds. “LEARNING IN PROGRESS” will be displayed on the screen while the LT2002 copies the Master Setup. When the Learning process is complete, a “LEARNING COMPLETE” message will be displayed.

7.When Learning is complete, disconnect the MPI cable from the Master TV.

(1)MEMORY 1 VER XX REV XX

(2)MEMORY 2 VER XX REV XX

(3)MEMORY 3 VER XX REV XX

(4)RETURN TO CLONE MENU

-TO CHANGE MENU ITEMS, PRESS CHANNEL KEYS OR DIGITS.

-TO EXECUTE ITEM, PRESS ON/OFF, POWER, OR ENTER.

206-4213 35