LG Electronics 50PC1RR*, 37LC2RR*, 42LC2RR*, 42PC1RR* owner manual Connections & Setup

Page 27

!NOTE

G To enjoy vivid picture and sound, connect a PC to the set.

G Avoid keeping a fixed image on the set’s screen for a long period of time. The fixed image may become permanently imprinted on the screen; use a screen saver when possible.

G Connect PC to the RGB (PC/DTV) or HDMI/DVI port of the set; change the resolution output of PC accordingly.

G There might be noise according to some resolu- tion, vertical pattern, contrast or brightness in PC mode. Change the PC mode into another resolu- tion or change the refresh rate into another rate or adjust the brightness and contrast on the menu until the picture is clean. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult it to the manufacturer of the PC graphic card.

G The synchronization input waveform for Horizontal and Vertical frequencies are separate.

G In 42PC1RR/50PC1RR models, we recommend using 1024x768, 60Hz for the PC mode, they provide the best picture quality.

G In 37LC2RR/42LC2RR models, we recommend using 1360x768, 60Hz for the PC mode, they provide the best picture quality.

G If the resolution of PC is over UXGA, there will be no picture on the set.

G Connect the signal cable from the monitor output port of the PC to the RGB (PC/DTV) port of the set or the signal cable from the HDMI output port of the PC to the HDMI/DVI port on the set.

G Connect the audio cable from the PC to the Audio input on the set. (Audio cables are not included with the set).

G If using a sound card, adjust PC sound as required. G This set uses a VESA Plug and Play Solution. The set provides EDID data to the PC system with a DDC protocol. The PC adjusts automatically when

using this set.

G DDC protocol is preset for RGB (Analog RGB), HDMI (Digital RGB) mode.

G If required, adjust the settings for Plug and Play functionally.

G If graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of either RGB (PC/DTV) or HDMI/DVI to display the PC on the set.

G If graphic card on the PC does output analog and digital RGB simultaneously, set the set to either RGB or HDMI; (the other mode is set to Plug and Play automatically by the set.)

G DOS mode may not work depending on video card if you use a HDMI to DVI cable.

G When you use too long RGB-PC cable, there might be a noise on the screen. We recommend using under 5m of the cable. It provides the best picture quality.

CONNECTIONS & SETUP

25

Downloaded From TV-Manual.com Manuals

Page 26 Page 28
Image 27
Page 26 Page 28
Contents No 38289U0564F 0611-REV03 LCD TV Plasma TVPage Accessories Contents TV Menu Controls IntroductionConnect a component video/audio device to these jacks Connect a Hdmi signal to HDMI/DVIConnection Option This is the back panel of 42PC1RR*, 50PC1RR* setsIntroduction This is the back panel of models 37LC2RR*, 42LC2RR* sets Mute Switches the sound on or off Remote Control KEY FunctionsRemote control effective range Installing BatteriesHome Menu Unfolding the Base Stand 42PC1RR InstallationReinstall the Cable Management as shown Arrange the cables as shown pictureConnect the cables as necessary Connections & Setup section HOW to Remove the Cable ManagementInstallation Short-circuit Breaker Stand InstallationDesktop Pedestal Installation Wall Mount Horizontal installationPoor signal areas, to get better picture quality Antenna ConnectionTo the right VCR Setup Appropriate programme between the TVVCR for viewing Button on the remote control If connected to AV2 Euro scart socketSelect AV2 input source External Equipment Connections When connecting with a S-Video cable DVD SetupPlease use the shield scart cable When connecting with a component cableWhen connecting with a D-sub 15 pin cable STBSET-TOP BOX SetupWhen connecting with a Hdmi to DVI cable PC Setup Connect RGB output of the PC toPC/DTV jack on the set Connections & Setup 720x400 800x60046.875 75.00 Turning the SET on Basic OperationFirst select your language Basic OperationTimeshift Special Functions DVR Digital Video Recorder‘Progress Bar’? Progressing the Timeshift FunctionPress the button to jump at the front of the programme Using the remote controlButton to speed up PressInstant Record RecordingAfter adjusting the recording time, select OK. The Status Screen being recorded Watching & RecordUse the D or E button for page up/down navigation Recorded TVPlaying Recorded Programs Play a recorded programThen press the OK button to display the progress bar If you press the Stop button, you can watch set Using the Remote ControlManual Recording After setting the Manual Rec , press the O K buttonVideo Quality Scheduled ListIf you press the G button, this message is displayed Format Hard DiskPIP PICTURE-IN-PICTURE Feature Adjusting PIP Transparency PIP Mode onlyWatching PIP Moving the PIP PIP Mode only Adjusting the Screen for the PIPSelecting AN Input Signal Source for the PIP SUB Picture Size Adjustment PIP Mode onlySwapping Between Main and SUB Pictures POP PICTURE-OUT-OF-PICTURE Channel ScanPress the Swap button to exchange the main and sub pictures Teletext Language Selection Option Switch ON/OFFSelection Simple Text OptionTOP Text Option FastextTime Special Teletext FunctionsSize HoldTV Menu On Screen Menus Selection and AdjustmentPress the E button to select Start Auto Programme TuningUSA / Korea / Philippines option Press the E button to select Storage fromPress the O K button to store it Manual Programme TuningPress the E button to select Search Is found the search will stopFine Tuning Press the OK buttonNumber during programme selection Assigning a Station Name Press the G button and then use D / E button to select Booster OptionProgramme Edit Favourite Programme Press the List button to return to normal TV viewing Calling the Programme TablePSM Picture Status Memory TV MenuCSM Colour Status Memory Manual Colour Temperature Control CSM User Option Picture FunctionSRGB Function ACM Active Colour Management Manual Picture Control SSM Sound Status Memory TV Menu Sound Menu OptionsAVL Auto Volume Leveler TV Speaker Adjusting Sound ControlLanguage selection for dual language broadcast STEREO/DUAL ReceptionOn Screen Display BroadcastSound Output Selection Nicam Reception OptionSetting the Clock Setting the ON/OFF Time Auto Sleep Sleep TimerChild Lock TV Menu Special Menu OptionsNormal White washOrbiter InversionDemo LOW PowerIndex Option You can switch Front Display on or offAuto config Auto ConfigScreen menu Manual ConfigManual config Press the Menu button and then D / E button to selectSelecting Wide XGA/VGA Mode Setting Picture Format Cinema Initializing NR Noise ReductionHow to connect external control equipment External Control Device SetupRS-232C Setup Type of Connector D-Sub 9-Pin MaleSet ID RS-232C ConfigurationsTransmission / Receiving Protocol Command Reference ListTransmission ka Set ID DataCr Transmission kl Set ID DataCr This feature is not available for all models HDMI/DVI How to Connect Remote Control IR Codes NEC FormatIR Codes Code Function Remote Control IR CodesProgramming the Remote Programming a code into a remote modeVCRs Programming CodesCatv Hdstb Audio Operation does not work normally Troubleshooting ChecklistReinstall the PC video card Check the signal cableExtended Absence MaintenanceCleaning the Screen Cleaning the CabinetProduct Specifications Environment condition Operating Humidity
Top Page Image Contents