LG Electronics 37LC2RR*, 42LC2RR*, 42PC1RR* Progressing the Timeshift Function, ‘Progress Bar’?

Page 32

SPECIAL FUNCTIONS

DVR (Digital Video Recorder)

PROGRESSING THE TIMESHIFT FUNCTION

1

2

3

4

1After selecting the Timeshift On, press the OK button.

As soon as Timeshift starts, a progress bar indicating the current recording status is displayed in the bottom of the screen.

Press the EXIT button to hide the ‘Progress Bar’ or press the OK button to display the 'Progress Bar'.

This function is preserved even change a programme on progressing the Timeshift.

2When finishing the Timeshift function, enter the option menu and turn Timeshift Off.

The ‘Progress Bar’?

This function indicates a possible DVR reshowing section ,a current on-screen and real on-broad- casting position, a section of section-recording.

1Status of current displayed video.

2Current save time.

315 minute intervals from Timeshift start time. (Total - one hour).

4Indicates current Timeshift position.

SPECIAL

!NOTE

FUNCTIONS

DVR (Digital Video Recorder) : A device which records and plays broadcast program contents onto a hard disk in set or SET TOP BOX.

In order to save hard-disk space, nothing is saved when there is no signal.

The total storage space of the hard-disk is 80 GB. 4 GB minimum is reserved for Timeshift.

When turning power on, it may take up to maximum 3 minutes to initialize the HDD.

The Recording function will not initiate for a copy-protected program.

Because an analog broadcast is transfered to a digital signal, video that contains rapid move- ment may show "cross stripes". This happens when the analog signal is compressed and then restored in the digital signal. The unit will attempt to reduce this excessive picture noise.

When using the PIP/DW, POP mode, Timeshift is stopped.

Timeshift is available in TV, AV1, AV2, S-Video2, AV3, AV4 mode.

Timeshift is not available for Audio only channels.

30

Downloaded From TV-Manual.com Manuals

Image 32
Contents LCD TV Plasma TV No 38289U0564F 0611-REV03Page Accessories Contents TV Menu Introduction ControlsConnect a Hdmi signal to HDMI/DVI Connection OptionThis is the back panel of 42PC1RR*, 50PC1RR* sets Connect a component video/audio device to these jacksIntroduction This is the back panel of models 37LC2RR*, 42LC2RR* sets Remote Control KEY Functions Mute Switches the sound on or offInstalling Batteries Remote control effective rangeHome Menu Installation Unfolding the Base Stand 42PC1RRConnect the cables as necessary Reinstall the Cable Management as shownArrange the cables as shown picture HOW to Remove the Cable Management Connections & Setup sectionInstallation Stand Installation Desktop Pedestal InstallationWall Mount Horizontal installation Short-circuit BreakerTo the right Poor signal areas, to get better picture qualityAntenna Connection VCR for viewing VCR SetupAppropriate programme between the TV Select AV2 input source Button on the remote controlIf connected to AV2 Euro scart socket External Equipment Connections DVD Setup When connecting with a S-Video cableWhen connecting with a component cable Please use the shield scart cableSTBSET-TOP BOX Setup When connecting with a D-sub 15 pin cableWhen connecting with a Hdmi to DVI cable PC/DTV jack on the set PC SetupConnect RGB output of the PC to Connections & Setup 46.875 75.00 720x400800x600 Basic Operation Turning the SET onBasic Operation First select your languageSpecial Functions DVR Digital Video Recorder TimeshiftProgressing the Timeshift Function ‘Progress Bar’?Using the remote control Button to speed upPress Press the button to jump at the front of the programmeRecording Instant RecordAfter adjusting the recording time, select OK. The Status Watching & Record Screen being recordedRecorded TV Use the D or E button for page up/down navigationThen press the OK button to display the progress bar Playing Recorded ProgramsPlay a recorded program Using the Remote Control If you press the Stop button, you can watch setAfter setting the Manual Rec , press the O K button Manual RecordingScheduled List Video QualityFormat Hard Disk If you press the G button, this message is displayedWatching PIP PIP PICTURE-IN-PICTURE FeatureAdjusting PIP Transparency PIP Mode only Adjusting the Screen for the PIP Selecting AN Input Signal Source for the PIPSUB Picture Size Adjustment PIP Mode only Moving the PIP PIP Mode onlyPress the Swap button to exchange the main and sub pictures Swapping Between Main and SUB PicturesPOP PICTURE-OUT-OF-PICTURE Channel Scan Switch ON/OFF Teletext Language Selection OptionSimple Text Option TOP Text OptionFastext SelectionSpecial Teletext Functions SizeHold TimeOn Screen Menus Selection and Adjustment TV MenuAuto Programme Tuning USA / Korea / Philippines optionPress the E button to select Storage from Press the E button to select StartManual Programme Tuning Press the E button to select SearchIs found the search will stop Press the O K button to store itNumber during programme selection Fine TuningPress the OK button Assigning a Station Name Booster Option Press the G button and then use D / E button to selectProgramme Edit Favourite Programme Calling the Programme Table Press the List button to return to normal TV viewingTV Menu PSM Picture Status MemoryCSM Colour Status Memory Manual Colour Temperature Control CSM User Option Function PictureSRGB Function ACM Active Colour Management Manual Picture Control TV Menu Sound Menu Options SSM Sound Status MemoryAVL Auto Volume Leveler Adjusting Sound Control TV SpeakerSTEREO/DUAL Reception On Screen DisplayBroadcast Language selection for dual language broadcastNicam Reception Option Sound Output SelectionSetting the Clock Setting the ON/OFF Time Sleep Timer Auto SleepTV Menu Special Menu Options Child LockWhite wash OrbiterInversion NormalLOW Power DemoYou can switch Front Display on or off Index OptionAuto Config Auto configManual Config Manual configPress the Menu button and then D / E button to select Screen menuSelecting Wide XGA/VGA Mode Setting Picture Format Cinema NR Noise Reduction InitializingExternal Control Device Setup RS-232C SetupType of Connector D-Sub 9-Pin Male How to connect external control equipmentRS-232C Configurations Set IDCommand Reference List Transmission / Receiving ProtocolTransmission ka Set ID DataCr Transmission kl Set ID DataCr This feature is not available for all models HDMI/DVI IR Codes How to ConnectRemote Control IR Codes NEC Format Remote Control IR Codes Code FunctionProgramming a code into a remote mode Programming the RemoteProgramming Codes VCRsCatv Hdstb Audio Troubleshooting Checklist Operation does not work normallyCheck the signal cable Reinstall the PC video cardMaintenance Cleaning the ScreenCleaning the Cabinet Extended AbsenceProduct Specifications Environment condition Operating Humidity