COMMERCIAL MODE
INSTALLER OVERVIEW
Following is the Commercial Mode Operation Setup.
Operating Installer Menu
To set up the controls for the TV you will need to know how to enter the 26LH1DC3/4/5 Installer menu and make changes to the default values as required. If necessary, familiarize yourself with the 26LH1DC3/4/5 Installer menu and how to make and save changes in the menu.
Optional Installer Remote
You will need an Installer remote control similar to the one shown to the right.
| The TV’s clonable features need to be set up before | |||||||||
| done. |
| ||||||||
| This is a critical step. | |||||||||
| If the Master TV display panel’s clonable features like: Clock Set, adding | |||||||||
| channel icons and channel labels, etc. are not done properly, then the | |||||||||
COMMERCIAL | cloned 26LH1DC3/4/5 TVs will all have problems. For example, do not do | |||||||||
you need to start the procedure over, then begin by setting installer item | ||||||||||
117 to 001, and pressing Enter to reset the TV to default values in the | ||||||||||
installer menu. You can do | ||||||||||
mode is limited to only editing channel icons and channel labels. | ||||||||||
|
|
|
|
|
|
|
|
|
| |
MODE | Refer to the appropriate section in the Manual for other TV features: | |||||||||
Picture, Sound etc. |
| |||||||||
| *Note: Digital Font options are available only after a channel search has | |||||||||
| been run and when the TV is tuned to an active digital channel with digital | |||||||||
| captions. |
| ||||||||
| LT2002 Clone Programmer | |||||||||
| As the cloning procedure is being performed, specific steps need to | |||||||||
|
|
|
|
|
|
|
|
|
| be done at the indicated times to achieve the |
|
|
|
|
|
|
|
|
|
| desired result. Be sure to do each cloning task as |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| indicated. If a procedure or step is left out or not |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| performed correctly, then the TV setup will be wrong |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| and cloning may not work. At each step, pay |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| attention to assure the TV screen shows the proper |
|
|
|
|
|
|
|
|
|
| message(s) when cloning. If the message indicated |
|
|
|
|
|
|
|
|
|
| does not appear, there is a problem with that step |
|
| ¤ |
|
|
| and cloning may not be successful. Cloning is only | ||||
|
|
|
|
|
|
|
|
|
| |
|
| QuickSet II Programmer |
| possible when the signal source is an Analog channel, | ||||||
|
|
|
| LT2002 |
| |||||
|
|
|
|
|
|
|
|
|
| not a digital channel. |
|
|
|
|
|
|
|
|
|
|
|
LODGING PTC INSTALLER MENU
000 | INSTALLER SEQ | 000 |
|
|
|
UPN | FPGA 09F1 | |
PTC V1.00.000 | CPU V1.01.00 | |
|
|
|
Typical Installer Menu
52