LG Electronics 26LH1DC5 manual Cloning Procedure Troubleshooting, Reset Clone After Static Shock

Page 71

CLONING PROCEDURE TROUBLESHOOTING

IMPORTANT INSTALLER SETUP INFORMATION! PLEASE READ THE FOLLOWING...

Warning: Do not use LT2002 while a LodgeNet PPV card is installed in TV or clone programmer will be damaged.

Reset Clone After Static Shock

After replacing exhausted batteries, or if the programmer behaves strangely after a static shock, activate the internal reset switch and restore normal operation.

After a reset, check the real-time clock setting. It may be necessary to reset the Clone Programmer clock from a TV containing the correct time.

*Note: The LT2002 programmer is designed to be used with TVs containing the 221-01006 and later processors. Use with earlier TV sets may give unpredictable results. Processors used before the 221-01006-04 have a limited screen display capability. They cannot display entire screens as shown in the quick setup instructions accompanying the LT2002 clone programmer. Use

the printed menu illustrations on the quick setup sheet supplied with the Clone as an aid to making your programming choices. (Although the menus are not all displayed, the clone functions all operate normally.)

Remote does not operate clone.

Wrong Installer remote. 8 Only use an appropriate Installer remote to operate clone programmer with 26LH1DC3/4/5.

LED does not blink

M.P.I. cord not connected.

 

8

Connect M.P.I. cord.

26LH1DC3/4/5 not

 

8

26LH1DC3/4/5 must be powered On for clone to work.

turned on.

 

 

 

 

Weak batteries.

 

8

Install 4 fresh AA high-quality alkaline batteries.

Clone menu hard to read.

Weak signal. 8 Connect 26LH1DC3/4/5 to a reliable Analog channel signal source.

No time set.

Time not available.

8 Set time on a TV, copy time to Clone Programmer.

 

 

APPENDIX

71

Image 71
Contents Installation and Operating Guide Party Responsible for Product Compliance Regulatory InformationCleaning and Disinfection Important Safety Instructions Safety InstructionsContents Preparation AccessoriesPreparation Remote Control SensorFront Panel Information Here shown may be somewhat different from your TV Back Panel InformationTV Swivel Stand Vesa Wall MauntingAntenna or Cable Connection External Equipment SetupExternal Equipment Setup Setup HD Receiver SetupWhen connecting Hdmi cable External Equipment SetupWhen connecting Hdmi to DVI cable Setup DVD SetupInput jacks on the set Connect the S-VIDEO output of the VCR toVideo input on the set Connect the audio outputs of the VCR to the a UdioProduct bearing this phenomenon VCR SetupWhen connecting with a RCA cable Digital Audio Output External Equipment SetupConnect the DVI output of the PC to the HDMI/DVI PC SetupExternal Equipment Overview Screen Setup for PC ModeComputer PC Hookup DVI Hookup to RJP or DVD PlayerWatching TV / Channel Control User Remote Control Button FunctionsWatching TV / Channel Control Number Keypad Installer Remote Control Button FunctionsSAP Display ON-SCREEN Menus SelectionChannel Channel SearchAuto Program Channel Search Watching TVChannel List Add the label to the channel Watching TV /CHANNEL ControlUnstable Screen Checking the Strength of the Digital SignalTime Time SettingClock Setting Manual Time SettingsHours Automatic Time SettingsTime Setting Daylight Saving Time SettingTime Zone Settings TV Deactivation Time Settings TV Activation Time SettingsAuto Off Parental CONTROL/RATINGS SET Password & Lock SystemEntering a PIN Password Parental CONTROL/RATINGSSet Block Hour Parental CONTROL/RATINGSTvpg Ratings Movie & TV RatingsDescription of the Mpaa and TV FCC Rating Codes Mpaa RatingsRestricting movies by their rating Canadian French Ratings Canadian English RatingsDownloadable Rating Turn Captions On/Off Analog ModeSound & Language Control Caption / TextLanguage Digital Captions ModeUse the ADJ D or E button to choose Service 1-Service Digital Font OptionsSound & Language Control Preset Sound SettingsSound Setting Adjustment-User Mode Adjust the sound to suit your taste and room situationsSound & Language Control Sound Balance SetupDigital Audio Output Settings Analog Audio Settings Automatic Volume Control SettingsUse the a DJ D or E button to highlight Internal Speaker Digital Audio Language SettingsUsing External Speakers Sound & Language ControlMenu Language Menu Transparency and press the O K Enter button Menu Transparency SettingsSet ID Use the a DJ D or E button to highlightPicture Control Preset Picture SettingsPicture Preset Color Temperature SettingsPicture Control Manual Picture AdjustmentScreen Format Adjustments Picture ControlUse the a DJ D or E button to choose Noise Reduction Film Mode OptionsUse the a DJ D or E button to choose Film Mode Noise ReductionMode Commercial ModeInstaller Overview CommercialCommercial Mode Commercial Mode SetupCloning CONNECTIONS/LEARNING Setup Commercial ModeLearning the Master TV Setup Clone Programmer Learning SetupTeaching the Master Setup to Another 26LH1DC3/4/5 Cloning CONNECTIONS/TEACHING Setup000 Installer Menu Items 035 through Installer Menu= IRC Installer SequencePoll Rate Mute DisableSleep Timer Caption LockRJP Available = Green = VioletQuick Shutoff KEY LockStart Minor Channel Atsc Tune ModeSelects Atsc tuning mode 0=Virtual, 1=Physical Atsc BandPeference TV Features / Menus that can be ClonedTo go to the next channel Adding Channel Icons and Labels in the 2-5-4 + Menu ModeTo exit the menu when done press Menu Making a Master TV Detailed Information For Making a Master TVSoftware Version Check 26LH1DC3/4/5 Camport Auto Sense Operation 26LH1DC3/4/5 Aux Input Configuration 26LH1DC3/4/5 Aux Input ConfigurationAppendix TroubleshootingAppendix Appendix Wrong Installer menu Settings Software problemRemote not in TV Mode Audio muted Broadcast problem TV Speakers OffTurned on Weak batteries Cloning Procedure TroubleshootingReset Clone After Static Shock 26LH1DC3/4/5 notSteps omitted or not Procedure interruptedClone should only scan Channels once Different TV modelsClone Troubleshooting Flow Chart TV Operating Check OHM RF Cable Glossary of TermsInstaller Quick Setup Guide Page Page Product Specifications