PEFERENCE
Detailed Information For Making A Master TV
IMPORTANT INSTALLER SETUP INFORMATION! PLEASE READ THE FOLLOWING...
To set up a master TV you will need to know how to enter the 26LH1DC3/4/5 Installer menu and make changes to the default values as required. If necessary, familiarize yourself
with the 26LH1DC3/4/5 Installer menu and how to make and save changes in the menu, before attempting to clone the 26LH1DC3/4/5 Master TV setup.
You will also need an Installer remote control similar to the one shown in the front of this manual.
Finally, the TV’s clonable features need to be set up. This is a critical step. If the Master TV display panel’s clonable features like adding channel icons or channel
labels are not correctly added, then the cloned 26LH1DC3/4/5s TVs will all have problems.
As the cloning procedure is being performed, specific steps need to be done at the indicated times to achieve the desired result. Be sure to do each task as indicated. If a procedure or step is left out or not performed completely, cloning may not work. At each step, pay attention to assure the TV screen shows the proper message when
cloning. If the message indicated does not appear, there is a problem with that step and cloning may not be successful. Cloning is only possible when the signal source is an Analog channel, not a digital channel.
Making a Master TV
Detailed Instructions
The following describes the procedure for preparing a Master 26LH1DC3/4/5 for cloning and the procedure for adding Channel Icons and/or Labels.
Note 1: Disconnect all Aux inputs. Under certain conditions, Auto Program Scan is disabled if there is an Aux input active.
Note 2: Under certain conditions, changes to the input mode of the RGB inputs will not take effect until the power is cycled (TV is turned Off and On). To avoid confusion, disconnect all RGB inputs before entering the Installer menu.
1.Enter the 26LH1DC3/4/5 installer menu.
a. Reset the internal controller to factory default by accessing installer menu item 117 FACT DEFAULT, set it to 1 and press “ENTER”. The value will change back to 0 after the TV’s internal controller has been
restored to factory default condition.
b.Within the Installer menu, set the Installer menu items to the configuration required of your institution.
c.It is important to set the tuning band at this time, see
Installer menu item 03 BAND/AFC.
d.Set Installer menu item 28 – CH OVERIDE to 001 to allow access to the Auto Program and Channel List/Channel Label features in the Channel Menu.
Exit the Installer menu.
2.Access the Master TV menus and set the clonable options on the menus to the desired configuration. Refer to the Clonable Menu Features Chart on the see page 63.
3.Run Auto Program.
4.Enter the Channel List/Channel Label menu and edit the channel
Channels only.
5.Assign ICONs to the channels using the Channel Label Menu.
Note: You can add Channel ICONS typically network logos like ABC, NBC, PBS etc. in this step. Or, in Step 7, add Channel ICONS or labels for channels without Icons.
6.Transfer the TV setup: Enter the 26LH1DC3/4/5 installer menu.
Press ‘2’, ‘5’, ‘5’, ‘MENU’ to start the transfer of the TV’s setup to the 26LH1DC3/4/5. Once the transfer is complete, the system will exit the Installer menu.
Note: Only do
7.Edit/Add Channel ICONs and Channel Labels as needed. Enter Installer menu. With menu displayed, press 2-
See page 62 for detailed instructions:
-Editing/Adding Channel ICON and Labels on Master TV
-Changing a Channel’s ICON on Master TV
-Changing/Adding Channel Labels on Master TV
-Changing Source Labels on Master TV
8.Verify Master TV setup and feature configuration:
• Did you add Channel ICONS?
• Did you add Channel Labels?
• Did you add Aux Source Labels?
• Did you adjust all TV menu options as required? The TV master setup is now ready to be cloned. Go to the master TV cloning section or continue on to page 52.
After verifying master setup, enter the 26LH1DC3/4/5 Installer menu and set Installer menu item 028 Ch Overide to 000.
COMMERCIAL MODE
65