Mitsubishi WD-52631 manual DVD Player with Component Video, Receiver Stereo System

Chapter 2. TV Connections 31

DVD Player with Component Video

Component video cables and analog audio cables are required. These are not included with the TV.

1.Connect the component video cables from Y Pb Pr VIDEO OUT on the back of the DVD player to the COMPONENT jacks on the TV back panel, matching the red, green, and blue colored connec- tions.

2.Connect left (white) and right (red) stereo audio cables from AUDIO OUT on the back of the DVD player to COMPONENT/AUDIO LEFT and

RIGHT on the TV back panel.

						$0.10/&/5		.0/*503	
								065
47*%&0
						:		7*%&0
7*%&0		)%.* $0.1"5*#*-*5:				1C		-&'5
		7*%&0 JQQJQ
"6%*0		$0.10/&/5 $0.1"5*#*-*5:
		7*%&0 JQQJ
-&'5		%7** 1$ $0.1"5*#*-*5:		)%.*  %7* "6%*0		1S
.0/0								3*()5
		3&'&3 50 08/&34 (6*%&			
"6%*0			"6%*0
3*()5			-&'5					-&'5
			.0/0					"6%*0
		
								065
		*/165	"6%*0					3*()5
			3*()5
"/5   "69	"/5  ."*/ 64& 8*5)
		$BCMF$"3%™							
								-&'5
								1$%7*
								"6%*0
								3*()5
$BCMF$"3%™ 64& 8*5) "/5  $"3% 501
			)%.*					4&37*$&
						1$  %7*		1035
%*(*5"-		*&&& 
"6%*0
065
57 #BDL 1BOFM									
				-
				3
		"6%*0 065
				:					
				1C
				1S
			7*%&0 065
		%7% 1MBZFS #BDL 1BOFM

Figure 13. Connecting a DVD player with component video

IMPORTANT

See Appendix B for component video signal compatibility information.

For digital audio connections to your A/V receiver, see your DVD player and A/V receiver Owner’s Guides.

A/V Receiver (Stereo System)

Most setups require either a digital audio cable or analog stereo audio cables.

The TV makes all audio available in digital and analog formats. Analog audio coming into the TV is available in digital format on the DIGITAL AUDIO OUT jack.

Digital incoming audio is available in analog format on the AUDIO OUT LEFT/RIGHT jacks. Usually, only one of the following connections is required:

•To connect an analog A/V receiver

Connect left (white) and right (red) audio cables from

AUDIO OUT/LEFT and RIGHT on the TV back panel to the TV AUDIO INPUT on the A/V receiver.

•To connect a digital A/V receiver with Dolby Digital surround sound and PCM audio support

Connect one end of the digital audio cable to DIGITAL AUDIO OUT on the back of the TV. Connect the other end to the COAXIAL DIGITAL INPUT on the back of the A/V receiver.

						$0.10/&/5		.0/*503
								065
47*%&0
						:		7*%&0
7*%&0		)%.* $0.1"5*#*-*5:				1C		-&'5
		7*%&0 JQQJQ
"6%*0		$0.10/&/5 $0.1"5*#*-*5:
		7*%&0 JQQJ
-&'5		%7** 1$ $0.1"5*#*-*5:		)%.*  %7* "6%*0		1S
.0/0								3*()5
		3&'&3 50 08/&34 (6*%&			
"6%*0			"6%*0
3*()5			-&'5					-&'5
			.0/0					"6%*0
		
								065
		*/165	"6%*0					3*()5
			3*()5
"/5   "69	"/5  ."*/ 64& 8*5)
		$BCMF$"3%™
								-&'5
								1$%7*
								"6%*0
								3*()5
$BCMF$"3%™ 64& 8*5) "/5  $"3% 501
			)%.*					4&37*$&
						1$  %7*		1035
%*(*5"-		*&&& 
"6%*0
065

Figure 14. Connecting audio from the TV to an A/V receiver

Note:

On rare occasions, an HDMI signal may be copy-restricted and cannot be output from the TV as a digital signal. To hear these copy-protected signals through the A/V receiver, use connections for analog A/V receivers.

Check the A/V receiver’s Owner’s Guide for information concerning use of the digital input and switching between digital sound and analog stereo sound from the TV.