Denon DVD-800 manual Safety, Installation, Maintenance, Service

PRECAUTIONS

Before using this unit please read these operating instructions care- fully. Take special care to follow the warnings indicated on the unit itself as well as the safety suggestions listed below.

Afterwards keep them handy for future reference.

		Safety
	1.	Power Source— The unit should be connected to a power
started		supply only of the type described in the operating instructions or
		as marked on the unit. If you are not sure of the type of power
		supply to your home, consult your appliance dealer or local
Getting		power company.
	2.	Polarization— If the unit is equipped with a polarized AC power
		plug (a plug having one blade wider than the other), that plug will
		fit into the AC outlet only one way. This is a safety feature. If you
		are unable to insert the plug fully into the outlet, try reversing the
		plug. If the plug should still fail to fit, contact your electrician to
		replace your obsolete outlet. Do not defeat the safety purpose of
		the polarized plug.
	3.	Power Cord Protection— AC power supply cords should be
		routed so that they are not likely to be walked on or pinched by
		items placed upon or against them. Never take hold of the plug or
		cord if your hand is wet, and always grasp the plug body when
		connecting or disconnecting it.
	4.	Overloading— Do not overload wall outlets and extension cords
		as this can result in a risk of fire or electric shock.
	5.	Nonuse Periods— When the unit is not being used, turn the pow-
		er off. When left unused for a long time, the unit should be un-
		plugged from the household AC outlet.
	6.	Attachments— Do not use attachments not recommended by
		the unit manufacturer as they may cause hazards.

Installation

Environment

1.Water and Moisture— Do not use this unit near water— for ex- ample, near a bathtub, washbowl, swimming pool, or the like. Damp basements should also be avoided.

2.Condensation— Moisture may form on the lens in the following conditions…

³immediately after a heater has been turned on. ³in a steamy or very humid room.

³when the unit is suddenly moved from a cold environment to a warm one.

If moisture forms inside this unit, it may not operate properly. To correct this problem, turn on the power and wait about one hour for the moisture to evaporate.

3.Heat— The unit should be situated away from heat sources such as radiators and the like. It also should not be placed in tempera- tures less than 5eC (41eF) or greater than 35eC (95eF).

Do not place the unit

on amplifiers or equipment that may become hot.

Placement

1.Ventilation— The unit should be situated so that its location or position does not interfere with its proper ventilation. Allow 10 cm (4q) clearance from the rear of the unit.

2.Foreign Material— Care should be taken so that objects do not fall into and liquids are not spilled into the unit. Do not subject this unit to excessive smoke, dust, mechanical vibration, or shock.

3.Carts and Stands— The unit should be used only with a cart or stand that is recommended by the manufacturer.

The unit and cart combination should be moved with care. Quick stops, excessive force, and un- even surfaces may cause the unit and cart combi- nation to overturn.

4.Mounting— Any mounting of the appliance should follow the manufacturer’s instructions, and should use a mounting accesso- ry recommended by the manufacturer.

Maintenance

Disconnect this unit from the AC outlet before cleaning.

Clean the cabinet, panel and controls with a soft cloth lightly moist- ened with a mild detergent solution.

Do not use any type of abrasive pad, scouring powder or solvent such as alcohol or benzine.

Service

1.Damage Requiring Service— The unit should be serviced by qualified service personnel when:

(a)The AC power supply cord or the plug has been damaged; or

(b)Objects have fallen or liquid has been spilled into the unit; or

(c)The unit has been exposed to water; or

(d)The unit does not appear to operate normally or exhibits a marked change in performance; or

(e)The unit has been dropped, or the enclosure damaged.

2.Servicing— The user should not attempt to service the unit be- yond that described in the operating instructions. All other servic- ing should be referred to an authorized service personnel.

3.Replacement parts— When parts need replacing, ensure the servicer uses parts specified by the manufacturer or parts that have the same characteristics as the original parts. Unauthorized substitutes may result in fire, electric shock, or other hazards.

4.Safety check— After repairs or service, ask the servicer to per- form safety checks to confirm that the unit is in proper working condition.

The heat can damage the unit.