Humax IR-ACE M manual GB50, Manual Satellite Search

Page 51

Motorised System

6.To set the East Limit:

a) Select “Movement” and use the

buttons to move your

motor East or West until it is at the position you wish

to use as your East Limit. Use the

buttons to stop the

motor at the correct position.

 

b)Highlight the Store East Limit option and press the OK ( ) button to store the current position as your East Limit.

 

To set the West Limit:

 

 

a) Select “Movement” and use the

buttons to move your

 

 

motor East or West until it is at the position you wish

to use as your West Limit. Use the

buttons to stop the motor at the correct position.

b)Highlight the Store West Limit option and press the OK ( ) button to store the current position as your West Limit.

5.Manual Satellite Search

The purpose of this is to set the motor position manually for each satellite.

This is useful if the satellite you require is not available in the pre-programmed list (see 3 above). To do this, you must access the Satellite Settings menu. Proceed as follows:

1.Select “Service Searching” from the Main menu and press theOK ( ) button to display the Service Searching menu.

2.Select the Manual Search option and press the OK ( ) button to display the Manual Search menu. Select the relevant Alternative Antenna you are using for this satellite.

3.Enter the Frequency, Polarisation, Symbol Rate and FEC for a transponder on the satellite you wish to find. The transponder information should be unique to the satellite.

4.Select the Alternative Antenna option and press the OK ( ) button to display the Satellite Settings menu.

5. Highlight the DiSEqC Command Mode option and, using the buttons, change this to Installer.

6.Highlight the Satellite name option and use the buttons to select the satellite you want to find. Use others if the name of the satellite you want does not appear.

7.When you have selected the satellite you are looking for, go down to the Movement option, and

again using the

buttons, start the motor moving.

8.You should move the motor as far west as possible and then move it east so that you cover the motor’s complete movement range.

9.During the move from west to east, the Signal Quality bar should register a signal once. This is the satellite’s position. If there two or more different positions register a

signal, then you must choose another frequency that will be unique to the satellite you want.

10.Use the Signal level and Strength Quality bar at the bottom of the screen to judge the best position for the dish.

11.Use the buttons to stop the motor when required.

12.When you have found the best position for the dish, go to the Motor Control option, and using the

buttons, select “Store” and press theOK ( ) button. The position of the satellite should now be stored.

13.If you have not stored this position, it will be lost when you exit the menu.

14.Repeat the process for each satellite if required, remembering to use a different alternative antenna for each satellite.

GB50

Image 51
Contents Page Contents Liquids SafetyCopyright & Glossary CopyrightGlossary DiSEqC 1.2 Connection Connecting a Satellite antennaReferences DiSEqC 1.0 ConnectionSoftware Upgradeing Front Panel STB Connections+ Model IR-ACE M only Model IR-ACE M onlyRear Panel RF OUT RS-232CGB10 TV only with RCA / CinchTV with Terrestrial antenna With a Hi-fi SystemGB11 TV with Motorised System DiSEqCGB12 Remote Control UnitGB13 Information18 V-/V+ GB14 Service PartFunction Guide Information Box I-PlateGB15 Changing ServicesTeletext Service Volume ControlSoundtrack SubtitleGB16 GB17 Service ListConfiguration Service All ServiceGB18 Service FavouriteService Network Service AlphabeticalMain Menu Guide Quick GB20GB21 Now modeGB22 Weekly modeReserved mode Quick modeGB23 GB24 Menu Language System SettingLanguage Setting GB25Current Time Time SettingGB26 Subtitle LanguageSleep Time Wakeup Service NoGB27 Wakeup TimeAudio Output Output SettingScreen Mode GB28Display Format GB29GB30 Ntsc ModeUHF Tuning Other SettingOSD Transparency Service OrganisingMenu Mode GB31Organise TV Services Organise All ServicesGB32 GB33 GB34 Organise Favourite ServicesGB35 Organise Radio ServicesGB36 GB37 GB38 Organise Networks GB39Delete Satellites GB40Service Searching Antenna SettingGB41 Manual Search GB42GB43 Automatic Search Symbol Rate tableoptionalGuide of Main Menu GB44GB45 StatusSmart card Information Conditional AccessGB46 Version InformationMail Messages GB47Monitoring EMM/ECM GB48 Satellite Setting Menu OptionsSetting your Receiver for DiSEqC Motorised SystemMotor Limit Setting GB49Initial Satellite Position Search Manual Satellite Search GB50Searching for services on your selected Satellite GB51Moving to a pre-set satellite GB52 GB53 Troubleshooting GuideGB54 Menu MapGB55 Specification GB57 Power SupplyPhysical Specifications Data In/Out