Humax IRCI-5400Z manual Motorised system, E31

Page 34

Motorised system

DiSEqC 1.2 User Instructions

If you have a DiSEqC 1.2 motorised system, then you can use the DiSEqC 1.2 functions available. The following instruction describes how to use the DiSEqC 1.2 functions to store the positions of the satellites and to search for the services(STAB Rotor Sat motor recommended).

1. Satellite Setting Menu Options

When DiSEqC Motorised System is Enabled in the Antenna Setting, a new menu is available for

configuring the motor. This menu is called Satellite Setting and is accessed by pressing the button while the option Antenna Alternative is highlighted in the Manual Search menu.

The following options are available on the Satellite Setting menu.

Satellite Name

A selection of satellite names that can be used to identify a motor position. If the satellite name you require is not available, please use other. In installer mode the Satellite Name Reference refers to the 0 position of the motor.

Movement

In user mode this is used to fine-tune the position of the motor for better reception. In Installer mode this is used to search for the position of a satellite manually.

Motor Control

Search : Searches for services on the chosen transponder.

Goto

: Moves the motor to the stored position of the selected satellite name.

Store

: Stores the current position of the motor for the selected satellite name.

Reset

: Resets all stored positions of the motor relative to the 0 position.(Installer mode only)

DiSEqC Command Mode

Changes the current mode between Installer and User.

2. Setting your Receiver for DiSEqC 1.2

You must set your receiver up so that it is ready to use DiSEqC 1.2. To do so, do as follows

1.Press the Menu( )button, to display the Main Menu.

2.Select Service Searching option and press button, to display the Service Searching menu.

3.Select Antenna Setting option and press button, to display the Antenna Setting menu.

4.You must set up a separate antenna alternative for each satellite position required.

5.Select the name of the satellite you wish to use.

6.Select the correct LNB frequency for the LNB you are using.

7.Set the Motorised System to Enable using the buttons.

8.The option DiSEqC Input Selection should now be disabled.

This option is used for DiSEqC 1.0 and cannot be used in conjunction with DiSEqC 1.2.

Your receiver is now ready to use DiSEqC 1.2. To return to the Main Menu, use the button until you are at the Main Menu.

E31

Image 34
Contents Page Contents Safety +/P Remote Control Unit+/V RCL Recall+/V 15 OK16 P+/P 18 EPGCopyright Copyright & GlossaryGlossary RS-232C STB ConnectionsFront & Rear Panel 12V OUTTV with VCR TV onlyWith Hi-Fi System TV with VCR and Motorised System DiSEqC Connect a Satellite antenna ReferenceConnect DiSEqC Loop ThroughGuide of Functions Changing ServicesSERVICE-PART Left side of the box Information Box I-PlateSubtitle Volume ControlSoundtrack TeletextGuide of Main Menu Advanced Service List Simple Service ListE12 Service Genre Service FavouriteService Network Service Alphabet OrderWeekly mode Now / Next modeE14 Quick mode Reserved modeE15 Language Setting System SettingE16 Guide of Main Menu Time Setting E17UHF Tuning Output SettingE18 Organise TV Services Service OrganisingOther Setting E19E20 E21 E22 Organise Radio ServicesYou can edit services using the network unit Organise NetworksE23 Service SearchingAntenna Setting Antenna AlternativeE24 Found services OSD Service Search OSDE25 E26 Manual SearchAdvanced Search LNB PowerE27 Video PID/Audio PID/PCR PIDAutomatic Search Detail ModeE28 Search TypeCommon Interface Signal DetectionStatus E29Version Information Conditional Access for Irdeto EmbeddedE30 Smart card InformationMotorised system E31E32 Initial Satellite Position SearchE33 To set the West LimitE34 Moving to a pre-set SatelliteTroubleshooting Guide Menu Map E36E37 Specification E38E39 CH36 or TBD. Software changable by MenuInhalt Nähe einer Heizquelle auf SicherheitshinweiseReinigungsmitteln auszusetzen Stellen Sie keine anderen elektrischen Geräte auf die STBFernbedienung 18 EPG Warnung Copyright & GlossarGlossar Anschlüsse der Set-Top Box Vorder- und RückseiteFernseher mit Videokassettenrekorder Nur FernseherMit einem Hi-Fi System Page Anschließen einer Satellitenantenne ReferenzenAnschließen des DiSEqC DurchschleifenProgrammwechsel FunktionenInformation Box Informationstafel Programmteil linke Seite der BoxUntertitel LautstärkenregelungTonspur VideotextTV Programmführer HauptmenüWähle Programm KindersicherungFortgeschrittene Programmliste D12Einfache Programmliste Alle ProgrammeProgrammanbieter D13Favorit GenreSo wählen Sie den TV/Radioführer D14So beginnen Sie mit dem Modus TV Programmführer Modus Jetzt / Modus NächsteWeiße Taste D15Modus Reserviert Modus SchnellMenüsprache D16Systemeinstellung AudiospracheD17 ZeiteinstellungAusgangseinstellungen D18UHF Abstimmung Andere Einstellungen ProgrammorganisationD19 Organisiere TV-ProgrammeD20 D21 Organisiere Radioprogramme D22Organisiere Netzanbieter Antenneneinstellungen ProgrammsuchlaufD23 Alternative AntenneD24 Gefundene Programme OSD D25Programm-Suchlauf OSD Verlassen ohne zu speichernManueller Suchlauf SymbolrateD26 Netzanbieter SuchlaufVideo PID/ Audio PID/ PCR PID D27Fortgeschrittener Suchlauf Smatv SuchlaufWählen Sie die Zielantenne für den automatischen Suchlauf D28Automatischer Suchlauf Suchlauf TypD29 SignalerfassungAllgemeine Schnittstelle EmpfängerstatusD30 Zugangsmodul für IrdetoAdressierte Mittelungen Motorisiertes System D31D32 Einstellung des AntennenmotorsD33 Bewegen zu einem voreingestellten SatellitenMenüübersicht D36D37 Technische Daten D38D39