Humax Digital Set-Top Box manual GB48, Manual Satellite Search

Page 49

Motorised System

6.To set the East Limit:

a) Select “Movement” and use the

buttons to move your

motor East or West until it is at the position you wish

to use as your East Limit. Use the

buttons to stop the

motor at the correct position.

 

b)Highlight the Store East Limit option and press the OK ( ) button to store the current position as your East Limit.

 

To set the West Limit:

 

 

a) Select “Movement” and use the

buttons to move your

 

 

motor East or West until it is at the position you wish

to use as your West Limit. Use the

buttons to stop the motor at the correct position.

b)Highlight the Store West Limit option and press the OK ( ) button to store the current position as your West Limit.

5.Manual Satellite Search

The purpose of this is to set the motor position manually for each satellite.

This is useful if the satellite you require is not available in the pre-programmed list (see 3 above). To do this, you must access the Satellite Settings menu. Proceed as follows:

1.Select “Service Searching” from the Main menu and press theOK ( ) button to display the Service Searching menu.

2.Select the Manual Search option and press the OK ( ) button to display the Manual Search menu. Select the relevant Alternative Antenna you are using for this satellite.

3.Enter the Frequency, Polarisation, Symbol Rate and FEC for a transponder on the satellite you wish to find. The transponder information should be unique to the satellite.

4.Select the Alternative Antenna option and press the OK ( ) button to display the Satellite Settings menu.

5. Highlight the DiSEqC Command Mode option and, using the buttons, change this to Installer.

6.Highlight the Satellite name option and use the buttons to select the satellite you want to find. Use others if the name of the satellite you want does not appear.

7.When you have selected the satellite you are looking for, go down to the Movement option, and

again using the

buttons, start the motor moving.

8.You should move the motor as far west as possible and then move it east so that you cover the motor’s complete movement range.

9.During the move from west to east, the Signal Quality bar should register a signal once. This is the satellite’s position. If there two or more different positions register a

signal, then you must choose another frequency that will be unique to the satellite you want.

10.Use the Signal level and Strength Quality bar at the bottom of the screen to judge the best position for the dish.

11.Use the buttons to stop the motor when required.

12.When you have found the best position for the dish, go to the Motor Control option, and using the

buttons, select “Store” and press theOK ( ) button. The position of the satellite should now be stored.

13.If you have not stored this position, it will be lost when you exit the menu.

14.Repeat the process for each satellite if required, remembering to use a different alternative antenna for each satellite.

GB48

Image 49
Contents Digital Set-Top Box with Irdeto embedded Contents Liquids SafetyCopyright Copyright & GlossaryGlossary References Connecting a Satellite antennaDiSEqC 1.0 Connection DiSEqC 1.2 ConnectionSoftware Upgradeing Front Panel STB ConnectionsRS-232C Rear PanelTV with VCR TV onlyWith a Hi-fi System TV with VCR and Motorised System DiSEqC GB10 Remote Control Unit18 V-/V+ InformationFunction Guide Service PartInformation Box I-Plate GB12Teletext Service Changing ServicesVolume Control GB13Subtitle SoundtrackGB14 Configuration Service Service ListAll Service GB15Service Network Service FavouriteService Alphabetical GB16Main Menu Guide Quick GB18GB19 Now modeGB20 Weekly modeQuick mode Reserved modeGB21 GB22 Language Setting System SettingGB23 Menu LanguageGB24 Time SettingSubtitle Language Current TimeGB25 Wakeup Service NoWakeup Time Sleep TimeGB26 Output SettingVideo Output CVBS/S-Video/RGB Audio OutputGB27 Screen ModeDisplay Format Other Setting Ntsc ModeGB28 Menu Mode Service OrganisingGB29 OSD TransparencyOrganise All Services Organise TV ServicesGB30 GB31 GB32 Organise Favourite ServicesGB33 Organise Radio ServicesGB34 GB35 GB36 Organise Networks GB37Delete Satellites GB38Antenna Setting Service SearchingGB39 Manual Search GB40GB41 Guide of Main Menu Symbol Rate tableoptionalGB42 Automatic SearchGB43 StatusGB44 Conditional AccessVersion Information Smart card InformationGB45 Mail MessagesMonitoring EMM/ECM Setting your Receiver for DiSEqC Satellite Setting Menu OptionsMotorised System GB46GB47 Motor Limit SettingInitial Satellite Position Search Manual Satellite Search GB48GB49 Searching for services on your selected SatelliteMoving to a pre-set satellite GB50 GB51 Troubleshooting GuideGB52 Menu MapGB53 Specification Physical Specifications Power SupplyData In/Out GB55