DirecTV HIRD-B1 manual Hook Up the Audio/S-video Signals, Hook Up the Audio/Video Signals

Page 14
The S-video cable and jack
The Phone line and jack

HUGHES-BRAND DIRECTV SYSTEM OWNER’S MANUAL

Before choosing the best connection for your entertainment system, you should connect the phone line. This can be done by plugging one end of the provided telephone cable into the

PHONE LINE jack on the back of your digital satellite receiver and the other end into a telephone wall jack. If you do not have a telephone jack within reach, contact your

local phone company to arrange for a new jack to be installed or reorient your digital satellite receiver to be within reach of a telephone wall jack.

To suit specific needs, you may need to purchase additional connectors and/or cables. These are available from your dealer or electronic hardware stores. Choose which hookup method to use based on:

The capabilities of your TV and VCR.

Your desire to pass local programming through the digital satellite receiver.

Any other devices you want to include in the system (stereo, second VCR, etc.).

We will guide you through the decision and connection process. But first, position yourself or your equipment so that you are looking at the backs. Note the various input and output receptacles, their shapes, and how they are labeled. Then read through the rest of this hookup section before proceeding to an actual hookup.

Do not turn on the power yet. For your safety, leave your digital satellite receiver, TV, VCR, and any other devices to be connected unplugged while hooking them up.

Hook Up the Audio/S-video Signals

Only the newest, high-end TVs and VCRs have S-video inputs. VCRs that support S-video include Hi8 and SVHS types. Look on the back of your TV and VCR for this special jack. It will be

labeled something such as S-VIDEO IN. If you are unsure, you can see the type of connector that you are looking for on the back of your digital satellite receiver. If neither, the TV or VCR has this jack, proceed to the “Hook Up the Audio/Video Signals” section.

This video hookup will give you the sharpest picture of any of the hookups. Also, this hookup will allow you to view satellite programming and local broadcast simultaneously on TVs that offer a “picture in picture” (PIP) feature.

When using this hookup, you cannot use the digital satellite receiver as a switch to choose between satellite programming and local broadcasts. You will use the input selection that your TV and/or VCR offers to select the source.

If your VCR has S-video input…

use an S-video cable to connect the digital satellite receiver’s S-VIDEOoutput to the S-video input on your VCR. Also connect one pair of the digital satellite receiver’s audio outputs (Left and Right) to the audio inputs on your VCR.

If your TV has S-video input…

connect an S-video cable from the S-VIDEOoutput (either from the digital satellite receiver if available or the VCR) to the S-video input on the TV. Also connect the left and right audio outputs from the same device that the S-video is coming from and connect them to the TV.

If your hook-up is complete…

move on to the “Finishing Up” section.

Hook Up the Audio/Video Signals

Most high-end TVs and VCRs have phono-type audio and video inputs. Look at the back of your TV and VCR for three jacks—possibly color coded yellow, white and red. They will be

labeled something like IN (L and R), AUDIO IN, and VIDEO IN. If you are unsure, look at these connectors on the back of your digital satellite receiver. If you

The phono-type video cable and jack

PAGE 2-2

Image 14
Contents Model HIRD-B1 Directv or 1-800-204-USSB Important Safety Instructions Service Federal Comunications Commission FCC Regulatory Information Page Table of Contents Programming Your Remote Control How Does All This Work? HUGHES-BRAND Directv SystemWhat You Should Do First Digital Satellite Receiver Directv System ComponentsSatellite Antenna HUGHES-BRAND Directv System Remote Control MoviesSetting UP Your Directv System Choosing the Best ConnectionsHook Up the Audio/S-video Signals Hook Up the Audio/Video SignalsHook Up the RF Signals Setting UP Your Directv SystemFinishing Up Installing Batteries in Your Remote ControlNow You Can Turn It On Basic Navigation Front Panel vs. Remote Control KeysControlling the Digital Satellite Receiver Page Installing and Pointing Your 4 Satellite Dish Installation screen Determine Where to Point Your Satellite DishChoosing the Antenna Installation Site Alignment Result Pop-up PanelInstalling and Pointing Your Satellite Dish Page Selecting a Mounting Option Installing the Antenna onto a Wooden Surface Installation ProcedureInstalling and Pointing Your Satellite Dish Installing the Antenna onto a Brick Surface Installing the Antenna onto a Cinder Block Surface Toggler installation steps Installing the Antenna onto a Metal Pole Assembling the HANT-3S Antenna Attaching the Antenna Assembly to the Mast or PoleAttaching the Reflector onto the LNB Support Arm Grounding the Metal Pole Mount Grounding the Base PlateInstalling and Routing the LNB Coaxial Cable Connecting the Coaxial Cable to the LNB Attaching the LNB to the LNB Support ArmPositioning the Satellite Dish Connecting the Satellite DishRouting the LNB Cable to the Satellite Receiver Pointing the Dish Using the Box Method Page Authorizing Your Service UssbPage Channel Banner Watching Satellite ProgrammingBasic Channel Changing LogoBelt Information BannerOneLine Guide TurboTuneData Alternate ServicesAlt. Audio Page ON-SCREEN Guides Choosing the Guide StyleGeneral On-Screen Guide Features Using PreSelect to Schedule Programs for ViewingProgram Guide SM. Cell Program Guide LG. Cell Title Guide Logo GuideFiltering the Guides Theme FiltersChannel List Guide TimesDone Information ScreenClass Filters ViewPreSelect To View Cancel PreSelectCancel Purchase Buy $Show Times Your RECEIVER’S Menu System Menu OverviewMain Menu Places to go from the Main MenuThings to do on the Main Menu Setup MenuPlaces to go from the Setup Menu Scheduler Things to do on the Setup MenuCurrent settings overview Things to do on the Scheduler screenThings to do on the Check Mail screen Check MailPurchases MessageThings to do on the Purchases screen New CardPlaces to go from the Purchases screen Lock/Unlock Locking ProcedureUnlocking Procedure Things to do on the Preferences screen PreferencesPlaces to go from the Preferences screen Advanced Preferences Things to do on the Advanced Preferences screenData Port Factory DefaultsLimits Phone PrefixMax Rating Channel ListsThings to do on the Limits screen Max SpendingPlaces to go from the Channel Lists screen Things to do on the Channel Lists screenPlaces to go from the Installation screen InstallationThings to do on the Turbotune Setup screen Things to do on the Installation screenPosition System TestThings to do on the System Test screen Receiver TestCode Scan Programming the Remote ControlProgramming Your Remote 8 Control Code Entry Brand TelevisionsAUX Using the Remote Control Controlling Other Components Using the AUX ButtonAssigning a Device to a Different Device Key Page Limited Warranty Revision a