DirecTV HIRD-B1 Attaching the Reflector onto the LNB Support Arm, Assembling the HANT-3S Antenna

Page 30

HUGHES-BRAND DIRECTV SYSTEM OWNER’S MANUAL

Attaching the Reflector onto the LNB Support Arm

There are two possible antenna models that may have been included with your DIRECTV System. Refer to the section that applies to your antenna model. If you don’t know which model number you have, you should be able to identify it by the associated diagram.

Assembling the HANT-3_S Antenna

1)Insert a flat-head screw into one of the holes in the face of the reflector, as shown.

2) Install the mounting bracket of the LNB support arm onto the four flat-head screws, as shown.

3) Loosely install a ¼-inch nut onto the portion of each flat-head screw that sticks through the back of the reflector and mounting bracket.

4) Tighten the four ¼-inch nuts. The heads of the flat-head screws must be flush on the inside surface of the reflector to be securely fastened to the LNB support arm.

5) Install the cable clip as shown.

Attaching the Antenna Assembly to the Mast or Pole

Now that you have assembled the antenna you are ready to mount it on your previously installed mast or pole. While the diagrams may show an antenna

model that differs from the one you have, the same procedures apply.

1) If necessary, slightly loosen the azimuth nuts on the LNB support arm.

2) Slide the antenna assembly onto the mast or pole until the top of the mast stops at the bolt at the top of the mounting assembly.

3) Tighten the azimuth nuts enough so that the antenna assembly can rotate easily on the mast or pole.

4) The next step is to ground the antenna.

PAGE 4-12

Image 30
Contents Model HIRD-B1 Directv or 1-800-204-USSB Important Safety Instructions Service Federal Comunications Commission FCC Regulatory Information Page Table of Contents Programming Your Remote Control HUGHES-BRAND Directv System What You Should Do FirstHow Does All This Work? Directv System Components Satellite AntennaDigital Satellite Receiver HUGHES-BRAND Directv System Remote Control MoviesSetting UP Your Directv System Choosing the Best ConnectionsHook Up the Audio/S-video Signals Hook Up the Audio/Video SignalsHook Up the RF Signals Setting UP Your Directv SystemInstalling Batteries in Your Remote Control Now You Can Turn It OnFinishing Up Front Panel vs. Remote Control Keys Controlling the Digital Satellite ReceiverBasic Navigation Page Installing and Pointing Your 4 Satellite Dish Installation screen Determine Where to Point Your Satellite DishChoosing the Antenna Installation Site Alignment Result Pop-up PanelInstalling and Pointing Your Satellite Dish Page Selecting a Mounting Option Installing the Antenna onto a Wooden Surface Installation ProcedureInstalling and Pointing Your Satellite Dish Installing the Antenna onto a Brick Surface Installing the Antenna onto a Cinder Block Surface Toggler installation steps Installing the Antenna onto a Metal Pole Attaching the Antenna Assembly to the Mast or Pole Attaching the Reflector onto the LNB Support ArmAssembling the HANT-3S Antenna Grounding the Metal Pole Mount Grounding the Base PlateInstalling and Routing the LNB Coaxial Cable Connecting the Coaxial Cable to the LNB Attaching the LNB to the LNB Support ArmConnecting the Satellite Dish Routing the LNB Cable to the Satellite ReceiverPositioning the Satellite Dish Pointing the Dish Using the Box Method Page Authorizing Your Service UssbPage Watching Satellite Programming Basic Channel ChangingChannel Banner LogoBelt Information BannerOneLine Guide TurboTuneAlternate Services Alt. AudioData Page ON-SCREEN Guides Choosing the Guide StyleGeneral On-Screen Guide Features Using PreSelect to Schedule Programs for ViewingProgram Guide SM. Cell Program Guide LG. Cell Title Guide Logo GuideFiltering the Guides Theme FiltersChannel List Guide TimesDone Information ScreenClass Filters ViewPreSelect To View Cancel PreSelectCancel Purchase Buy $Show Times Your RECEIVER’S Menu System Menu OverviewMain Menu Places to go from the Main MenuSetup Menu Places to go from the Setup MenuThings to do on the Main Menu Scheduler Things to do on the Setup MenuCurrent settings overview Things to do on the Scheduler screenThings to do on the Check Mail screen Check MailPurchases MessageNew Card Places to go from the Purchases screenThings to do on the Purchases screen Locking Procedure Unlocking ProcedureLock/Unlock Preferences Places to go from the Preferences screenThings to do on the Preferences screen Advanced Preferences Things to do on the Advanced Preferences screenData Port Factory DefaultsLimits Phone PrefixMax Rating Channel ListsThings to do on the Limits screen Max SpendingPlaces to go from the Channel Lists screen Things to do on the Channel Lists screenPlaces to go from the Installation screen InstallationThings to do on the Turbotune Setup screen Things to do on the Installation screenPosition System TestThings to do on the System Test screen Receiver TestProgramming the Remote Control Programming Your Remote 8 ControlCode Scan Code Entry Brand TelevisionsAUX Using the Remote Control Controlling Other Components Using the AUX ButtonAssigning a Device to a Different Device Key Page Limited Warranty Revision a