Shaw SAC-00-094 manual Connecting Receiver and Dish, Fig. M

Page 7

Step 6: Attach the Quad Satellite LNB/Feedhorn Clamp Assembly to the Feed Support Arm. Loosen the Feed Arm screw enough to allow the clamp to fit snugly into the

Feed Support Arm. Securely tighten the Feed Arm screw.

Step 7: Using your compass, point the LNB in the direction corresponding to the SAT B azimuth setting (see Figure M). Draw a vertical mark overlapping the Clamp Mount Assembly and the mast. This mark will provide you with the approximate satellite location reference point when you’re ready totune to the satellite.

Fig. M

Step 8: Loosen the Skew Adjustment Bolts on either side of the Clamp Mount Assembly. Adjust the Skew Alignment Mark with the scale indicator to theSAT Bskew setting you recorded earlier. Finally, lock it in place by securely tightening the Skew Adjustment Bolts.

IMPORTANT: Do not make any further adjustments to the Skew Setting from this point onward.

Step 9: After making the permanent skew adjustment, install the (2) Hex Head Hi/Lo Screwsin the dish boss holes (see FigureC). Fourboss holes are available but you’l only need to usetwo (the other two may be obstructed depend ing on

￿You have just finished attaching theDish to the Universal Mount.the skew setting). Do not over tighten Hi/Lo Screws.

6.Connecting Receiver and Dish

Youare now at the point in the installation where one of the output ports of the QUAD LNBF neds to be connected ot the satellite input connector of the Motorola DSR satellite receiver.Refer to theInstallation Section of the Motorola User Guide andfollow the instructions on how to connect the cable from thesatellite dish to the satellite input terminal onthe satellite receiver’sback paneland how to connect the satellitereceiver to your TVset. Toview the receiver’s installer menu you must connect the receiver to a TV set to show you a relativescaled signal level meter that will assist youto align the dish tomaximum signal strength for your location.

1.Connect the coaxial RG6U cableprovided with theinstal kit to one of the ports of het QUADLNBF and connect het other end of the coaxial cableto the satelite receiver input connector. To make the dish alignment easier,suggest you locatereceiver and TVat an electrical outlet close to where the dish is installed. Unless you can view thesignal level on the TV screen from wherethe dishis being aligned, you will

7

require an assistant to monitor the signallevel reading on the TV as you align the dish for maximum signal.

2.When receiver is first powered up, ifeceiverr is tuned to channel 255 (factory default channel on receiver models DSR205 and DSR315),set receiver to channel284 prior to starting dish alignment. Otherwise, if receiver is set to channel 299 (factory default channel for newDSR5xx series, DSR207/209, DSR317/319), change channel to992prior to starting dish alignment.

For DSR205 and DSR315 receivers you shouldsee the following displayedon the TV when you first turn receiver on. Using remote tune receiver to ch 284 to alignthe dish.

For new DSR505, DSR530, DSR207/209 and DSR317/319 you should see the following displayed on your TV when you first turn receiver on. Receiver should be tuned to channel 299.

3.Once dish has been connected to thereceiver and receiver connected to the TV, follow the steps in the Motorola User Guide to access the installer menu.

To access this menu for DSR205 and DSR315 model receivers, using remote

1.Press Options,

2.Press 6 System Setup

3.Press 3 Installation settings

4.Press 1 Tune in Satellite Signal

Installer Menu for Motorola DSR205, DSR315 and DSR405 model series receiver.

SAC-00-094

Image 7
Contents Dual Satellite Phonex Easy Jack Welcome to Shaw DirectYou’ll need the following tools Hardware Getting StartedWe do not recommend Dish AssemblyDo not install the dish Mounting LocationsAzimuth Elevation Skew SAT a SAT B Locating the SatelliteYou’ve just finished assembling the dish You have just completed locating a site for your dish Attaching the DishFig. M Connecting Receiver and DishSignal Verification Aligning Dish To Acquire Shaw Direct SignalAlternate Tuning Method Fine TuningAuthorizing Receiver for Service Yoursystem is now inef tunedand ready foractivation Groundinghet Coaxial CableProblem #2 I can’t change channels Try each of the following TroubleshootingQuebec Satellite Locator ChartSatellite ‘A’ Satellite ‘B’ Town/City OntarioSaskatchewan ManitobaAlberta Yukon Territory Northwest Territory