Woods Equipment BH7500 manual Bolt Torque Chart, SAE Series Torque Chart

BOLT TORQUE CHART

Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application.

Fasteners must always be replaced with the same grade as specified in the manual parts list.

Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly.

All torque values are given to specifications used on hardware defined by SAE J1701 & J1701M JUL96.

SAE SERIES

ATORQUE

CHART

SAE Bolt Head

Identification

SAE Grade 2	SAE Grade 5	SAE Grade 8
(No Dashes)	(3 Radial Dashes)	(6 Radial Dashes)

A				MARKING ON HEAD
Diameter	Wrench	SAE 2			SAE 5		SAE 8
(Inches)	Size	Lbs.-Ft.	N-m	Lbs.-Ft.	N-m	Lbs.-Ft.	N-m
1/4”	7/16”	6	8	10	13	14	18
5/16”	1/2”	12	17	19	26	27	37
3/8”	9/16”	23	31	35	47	49	67
7/16”	5/8”	36	48	55	75	78	106
1/2”	3/4”	55	75	85	115	120	163
9/16”	13/16”	78	106	121	164	171	232
5/8”	15/16”	110	149	170	230	240	325
3/4”	1-1/8”	192	261	297	403	420	569
7/8”	1-15/16”	306	416	474	642	669	907
1”	1-1/2”	467	634	722	979	1020	1383
	METRIC SERIES		8.8	Metric Bolt Head		10.9
A	TORQUE
			Metric	Identification		Metric
	CHART
			Grade 8.8			Grade 10.9
A		COARSE THREAD			FINE THREAD		A

			MARKING ON HEAD				MARKING ON HEAD
Diameter &										Diameter &
		Metric 8.8		Metric 10.9		Metric 8.8		Metric 10.9
Thread Pitch	Wrench									Thread Pitch
(Millimeters)	Size	N-m	Lbs.-Ft.	N-m	Lbs.-Ft.	N-m	Lbs.-Ft.	N-m	Lbs.-Ft.	(Millimeters)
6 x 1.0	10 mm	8	6	11	8	8	6	11	8	6 x 1.0
8 x 1.25	13 mm	20	15	27	20	21	16	29	22	8 x 1.0
10 x 1.5	16 mm	39	29	54	40	41	30	57	42	10 x 1.25
12 x 1.75	18 mm	68	50	94	70	75	55	103	76	12 x 1.25
14 x 2.0	21 mm	109	80	151	111	118	87	163	120	14 x 1.5
16 x 2.0	24 mm	169	125	234	173	181	133	250	184	16 x 1.5
18 x 2.5	27 mm	234	172	323	239	263	194	363	268	18 x 1.5
20 x 2.5	30 mm	330	244	457	337	367	270	507	374	20 x 1.5
22 x 2.5	34 mm	451	332	623	460	495	365	684	505	22 x 1.5
24 x 3.0	36 mm	571	421	790	583	623	459	861	635	24 x 2.0
30 x 3.0	46 mm	1175	867	1626	1199	1258	928	1740	1283	30 x 2.0

Typical Washer Installations

Lock washer	Flat Washer
Bolt
Nut	8/9/00

30 APPENDIX

Bolt Torque & Size Charts (Rev. 9/5/00)