Woods Equipment BH7500 manual Operation

Page 5

SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

check and comply with these instructions may result in serious injury or death.

￿Remove seat and upper support assembly before installing or removing backhoe from tractor. Failure to comply may result in equipment failure and/or personal injury.

￿If tractor is equipped with draft sensing control, set control to “HEAVY” (minimum sensitivity) posi- tion.

￿On tractors equipped with optional “Draft Con- trol Hitch,” you must install the “Draft Lockout” (provided in sub-frame kit) into position as shown. Failure to install the “Draft Lockout” will allow upper hitch to move during backhoe operation and could result in operator injury.

￿Make sure all safety decals are installed. Replace if damaged. (See Safety Decals section for location.)

￿A minimum 25% of tractor and equipment weight must be on the tractor front wheels when attachments are in transport position. Without this weight, tractor could tip over, causing personal injury or death. The weight may be attained with a loader, front wheel weights, ballast in tires, or front tractor weights. Weigh the tractor and equipment. Do not estimate.

OPERATION

￿Do not allow bystanders in the area when oper- ating, attaching, removing, assembling, or servic- ing equipment.

￿Before operating, make sure stabilizer pads are lowered firmly to the ground. Stabilizer arms pro- vide support for the backhoe and support for the backhoe mounting brackets.

￿Do not operate equipment while under the influ- ence of alcohol or drugs.

￿Always comply with all state and local lighting and marking requirements.

￿Do not allow riders. Do not lift or carry anybody on the power unit or attachments.

￿The only time the backhoe may be operated from a position other than the operator seat is dur- ing backhoe attachment and removal. Operator must

Read Sub-Frame Mounting Kit Manual instructions on attaching and removing back-

hoe and use extreme care

Always stand between rear tire and backhoe stabilizer arms or along side of tractor to avoid being trapped should the boom swing control be accidentally activated.

￿Never leave equipment unattended with engine running or with bucket in raised position. Always engage swing and boom transport locks, relieve system pressure by operating controls, and remove ignition key before leaving equipment.

MAINTENANCE

￿Refer to backhoe manual and follow all mainte- nance safety rules and instructions.

￿Do not modify or alter or permit anyone else to modify or alter the equipment or any of its compo- nents in any way.

￿Your dealer can supply original equipment hydraulic accessories and repair parts. Substitute parts may not meet original equipment specifica- tions and may be dangerous.

￿Always wear relatively tight and belted clothing to avoid entanglement in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head.

￿Do not allow bystanders in the area when oper- ating, attaching, removing, assembling, or servic- ing equipment.

￿Make sure attachment is properly secured, adjusted, and in good operating condition.

￿Keep all persons away from operator control area while performing adjustments, service, or maintenance.

￿Before working on backhoe, extend boom and dipperstick and place bucket on ground. Make sure that all system pressure has been relieved by oper- ating controls before performing maintenance or service or before disconnecting any hydraulic lines.

￿Tighten all bolts, nuts and screws to torque chart specifications. Check that all cotter pins are installed securely to ensure equipment is in a safe condition before putting unit into service.

￿

BH6500/7500 SFMK 11/1/00

SAFETY 3

Image 5
Contents MAN0157 To the Dealer Table of Contents Installation Safety RulesOperation Backhoe SUB-FRAME Installation InstallationModify PTO Shield SUB-FRAME Installation Cont’dKioti 1470 Loader Front Mounting BracketsInstall Rear Mount Install Rear Hanger BracketSub-Frame Fit-Up Typical Sub-Frame Fit-UpTorque Specifications Attach Sub-Frame to Backhoe Sub-Frame Installed to BackhoeHydraulic Installation Hydraulic InstallationAssemble Pump Kit #9261 #9261 Pump Kit For BH6500/7500 Backhoe OnlyConnect Fittings to Hydraulic Manifold #1003179 Hose Kit For BH6500/7500 Backhoe & 1009 LoaderCont’d #1003179 Hose Kit for 1009 Loader Cont’dAssemble Backhoe Valve Hoses Assemble Loader Valve HosesConnect Hoses to Hydraulic Manifold 1009 Loader Only OperationConnect Hoses to Hydraulic Manifold Backhoe & Loader Backhoe & Loader Removed Connect Hoses to Hydraulic Manifold Backhoe OnlyConnect Fittings to Hydraulic Manifold #1003179 Hose Kit for 1012/1016 Loader Cont’d Return Port Fittings Installation#1003179 Hose Kit for 10012/10016 Loader Cont’d Connect Hoses to Hydraulic Manifold 1012/ 1016 Loader Only Loader Hose InstallationConnect Hoses to Hydraulic Manifold Backhoe & Loader Removed Mount Sub-Frame & Backhoe to Tractor Sub-Frame & Backhoe to TractorRemove Backhoe With Sub-Frame Sub-Frame & Backhoe to Tractor Cont’dStore Hydraulic Pump if Equipped Parts REF Part QTY Description #1003179 and #1002657 Hose Kits#1003179 and #1002656 Hose Kits #1003179 Hose kit for BH6500/7500 #1003179 and #1002656 Hose Kits Parts ListSAE Series Torque Chart Bolt Torque ChartBolt Size Chart Abbreviations Warranty Model No Part Warranted Duration MAN0157