Technicolor - Thomson IFC130 manual General operation

Page 8

IFC130-P_EN 5/08/05 9:48 Page 8

General operation

Switching the TV set on and off

To switch the TV set on:

-press the button on the side of the TV set, the or any numeric button on the remote control, or

-press the TV, OK or PR+/PR- buttons to switch the television on at the last channel or AV programme you were watching, or

-press the AV button to switch the television on at the last AV

EN

programme you were watching.

 

 

To put the TV set into standby mode, press the

 

button on the side of the TV set or the

button on the

remote control.The TV set remains powered up, but with low energy consumption.

To switch off the TV set, unplug the mains socket from the mains outlet.

Accessing channels

Using the numeric buttons:

for channels 1 to 9, press the corresponding numeric button;

for channels 10 to 99,

-press the tens digit for a few seconds to display it on the screen, then press the units digit. For instance, for programme 24, press and hold 2 to display 2-, then press 4; or

-press the 0/--button to display --”, then enter the two digits.

Using the PR+/PR- buttons: scroll through the channels. AV programmes are not included in the cycle unless you use the buttons on the side of the TV set.

Using the list of programmes: refer to page 9.

To access the channel or AV programme previously being watched, press the RETURN button.

Accessing your favourite channels

You can define the channels you watch most often as your favourite channels.This will allow you to create your own list of channels which you can access more quickly using the PR+/PR- buttons on the remote control.

1.Follow the procedure described in point 5 on page 6 for defining a channel as your favourite channel.

2.Press the PRESETS (red) button on the remote control.

3.Select the PR+/PR- keys option. Use the buttons to select Favourites.

When you change channels using the PR+/PR- buttons on the remote control only your favourite channels will be available.

To cancel this option, select All channels under the PR+/PR- keys option.

Note:The PR buttons on the TV set allow you to access all the channels set up, even if the Favourites option is selected

Accessing AV programmes

Press the AV button to display the last selected audio-visual programme and scan through the other audio-visual programmes.

AV selection loop:AV1,AV2,AV3, CMP (= component,YPrPb or YCrCb),VGA, HDMI.

Volume

Volume control: use the  VOL  buttons on the side of the TV set or press the +/- buttons on the remote control to increase or decrease the volume.

Sound mute: press the or button to temporarily mute the sound. Press this button again or the + button to restore it.

Headphone volume control: press the +/- buttons on the remote control to display the volume control bar.Then use the buttons to switch to the headphone volume control bar. Use the +/- buttons to adjust the volume.

Displaying status information

In TV mode you can press the INFO (yellow) button on the remote control to display the number and name of the relevant channel, the time and date, the type of sound and format or zoom. If the turn-off timer is set the relevant symbol is displayed, along with the time remaining until the TV set is switched off.

Press the GUIDE (blue) button on the remote control to display the name and the start time for the current programme and the following programme. If this information is not available you will receive a message to this effect.

In PC mode you can press the INFO (yellow) button on the remote control to display the time and date, the type of sound and format, as well as the source of the signal being received and the resolution.

When you switch the TV set on and change channels or exit Teletext, the channel’s number and name are displayed.

Note: If you activate the Channel number function in the Preferences menu, the channel number will be displayed permanently (see page 16).

8

Image 8
Contents Contents Safety Getting startedImportant information Plasma panelSwitching on Getting startedRemote control TV functions Using the remote control for other equipmentProgramming the remote control Playing files from memory cardsPR  PR  Programming the volume control functionManual programming Initial set-up Symbols. UseChannel set-up Repeat this procedure to find other channels Channel set-upManual channel set-up Belarussian GreekGeneral operation General operation Adjusting the sound Advanced functionsTone control SoundAdjusting the picture Headphone settingsHeadphone settings Advanced functionsOther settings Other settingsPC mode you can access a number of specific functions Setting the time Setting the time and dateUsing the calendar Programming a turn-off timerProgramming the wake-up timer Wake you usingParental control Defining a PIN codeLocking the Installation menu Operation TV modeLocking a channel or AV programme Locking the buttons on the TV setPreferences Customising your televisionPreferences Configuring AV sockets AV settingsPlaying mp3 and Jpeg files simultaneously Accessing Teletext TeletextNavigator Other Teletext functionsOther information SocketsConnecting active speakers or an amplifier Connecting headphonesConnecting a video recorder Other information