SET UP FOR USE
You can program the tuner to scan all the channels you receive in your area.
NOTE: Channel memory programming is NOT needed when connected to a cable box or satellite box. Just select the TV/VCR channel selector to the output channel of the cable box or satellite box (Ex CH3). Then select the channel to be viewed on the Cable Box or Satellite Box.
CHANNEL SET UP FOR THE
FIRST TIME
1Plug in the TV/VCR power cord
Plug the TV/VCR power cord into a standard AC outlet.
NOTES:
• You must disconnect the car battery cord from the TV/VCR before you use AC power.
•If some digits appear in the corner of
the screen, press the POWER button without unplugging the power cord.
2Turn on the TV/VCR
Press the POWER button to turn on the TV/VCR.
3Select “ENGLISH” or “ESPAÑOL”
Select “ENGLISH” or | – SET UP – | |
“ESPAÑOL”=Spanish using the | B LANGUAGE | |
F.FWD/B or REW/s button. “[ ]” | [ENGLISH] ESPAÑOL | |
AUTO PRESET | ||
indicate the selected language. | ||
|
4 Begin auto preset
Press the PLAY/K or STOP/L but- | – SET UP – | |
| ||
ton to point to “AUTO PRESET”. | LANGUAGE | |
Then press the F.FWD/B button. | [ENGLISH] ESPAÑOL | |
B AUTO PRESET | ||
The tuner scans and memorizes all | ||
| ||
active channels in your area. |
|
NOTES:
• The TV/VCR distinguishes between standard TV |
channels and cable channels. |
TO SELECT A DESIRED CHANNEL
You can select the desired channel by using the CHANNEL K or L button or directly pressing the number buttons on the remote control.
Note for using the number buttons:
•When selecting cable channels which are higher than 99, press the +100 button first, then, press the last two digits. (Example: to select channel 125, first press the +100 button then press “2” and “5”).
•You must proceed
CLOCK SET UP
(AUTO / MANUAL)
The TV/VCR clock must be set correctly before VCR timer recording is possible. It is suggested that the clock be set manually when first setting up the TV/VCR. Then, setup auto clock correction which will periodically correct the setting if necessary. NOTE: If you cannot receive a station with time signals, auto clock setting cannot be performed. Use manual setting only.
MANUAL CLOCK SETTING
Make sure ...
•The TV/VCR is turned on.
In the example below, the clock is to be set to:
DATE | May 6th, 2003 |
SETTING TIME | 5:40PM |
• If you want to play or record a video tape BEFORE |
presetting the tuner, you must press the MENU but- |
ton on the remote control. To preset the tuner again, |
see “CHANNEL SET UP AGAIN” on page 13. |
• The TV/VCR may recognize TV channels to be |
CATV channels by the receiving conditions. In this |
case, try auto preset again in the fine receiving |
conditions. |
1Select “SETTING CLOCK”
Press the MENU button on the remote control.
Press the PLAY/K or STOP/L button to point to “SETTING CLOCK”.
Then, press the F.FWD/B button.
– M E N U –
TIMER PROGRAMMING PICTURE CONTROL
BSETTING CLOCK CHANNEL SET UP USER’S SET UP LANGUAGE [ENGLISH] ZERO RETURN
TIME SEARCH
5After scanning
The tuner stops on the lowest memorized channel. If you want to recall the selected channels, you can select the desired channel directly with the remote control number buttons or CHANNEL K or L button.
2Select “MANUAL CLOCK SET”
Press the PLAY/K or STOP/L | – SETTING CLOCK – | |
button to point to “MANUAL | AUTO CLOCK | [ON] |
CLOCK SET”. | AUTO CLOCK CH SEARCH | |
AUTO CLOCK CH | [ 02 ] | |
| B MANUAL CLOCK SET |
|
Then, press the F.FWD/B button. | D.S.T. | [OFF] |
|
| |
- 11 - | EN |