![](/images/new-backgrounds/1247748/24774883x1.webp)
Function setup (DVD)
■ Display
On screen display can be switched on or off when you press any buttons.
Off: On screen displays do not appear when you | |
press any buttons. | |
On: On screen displays appear when you press | |
any buttons (factory setting). | |
■ Picture Mode | content in pictures |
There are two types of source | |
recorded in DVD video discs: film content (pictures | |
recorded from films at 24 | frames per second) and |
video content (video signals recorded at 30 frames per | |
second). Make this selection according to the type of | |
content being viewed. |
|
Auto: Select this selection normally.
The DVD player automatically detects source content, film or video of playback source, and converts that signal in the progressive output format in an appropriate method.
Film: The DVD player converts film content pictures in the progressive output format appropriately. Suitable for playback of film content pictures. The progressive output feature will be most effective under this selection.
Video: The DVD player filters video signal, and converts it in the progressive output format appropriately.
Suitable for playback of video content pictures.
Note: |
|
Depending on the disc, pictures may be cut off or doubled. In | |
this case, select “Video”. |
|
■ JPEG Interval | all JPEG files |
You can continuously playback | |
automatically. | disc will start playback on |
After the selection below, the | |
JPEG files which have been recorded. |
Off:
Plays back one file at a time.
5 Seconds:
Plays back images in the form of a slide show at 5 second intervals.
10 Seconds:
Plays back images in the form of a slide show at 10 second intervals.
15 Seconds:
Plays back images in the form of a slide show at 15 second intervals.
■ Screen Saver | operates when you leave the unit in |
The screen saver | |
DVD stop mode for | approx. five minutes. |
The DVD VIDEO logo moves randomly on the screen.
Off:
Screen Saver function is invalidated.
On:
Screen Saver function is made effective.
■ Night Mode
Night Mode enables you to control the dynamic range so as to achieve a suitable sound for your equipment.
Off: It plays back at the recording level on the disc.
On: Loud sound such as explosion is toned down slightly when played back. This is suitable when it is connected to a stereo.
Notes:
• This function works only when the disc recorded with Dolby Digital is played back.
• The level of Night Mode may differ depending on DVD video disc.
■ QSound
This DVD video player equipped with a “QSound”. It can produce the effect of being in a cinema or a concert hall.
Off: The QSound is disengaged.
On: The QSound operates.
Notes:
• The QSound setting can also be changed with AUDIO on the remote control 36 .
• This function works only when the disc recorded with Dolby Digital is played back.
• When this function works, the volume might changed.
• When the voice is distorted, turn off QSound.
■ Digital Out
You can select the digital output sound format corresponding to your system connection.
PCM:
Change Dolby Digital to PCM for the output.
Select when connected to a 2 channel digital stereo amplifier.
Bitstream:
Disc audio bitstream data will be output.
Off:
There is no sound output from DIGITAL AUDIO OUT jack.
Note:
Even if you select “Bitstream”, MPEG Audio will be output in PCM format.
■ Parental control setting
Some discs are specified as not suitable for children. Such discs can be limited not to playback with the unit.
1)Press ▲ or ▼ to select “Parental”, then press ENTER. “Enter Password” screen will appear.
2)Press “0000” using Number buttons
(Please note, this is
•Level Off: The parental control setting does not function.
•Level 8: Virtually all DVD software can be played back.
•Level 1: DVD software for adults cannot be played back.
3)Press ▲ or ▼ to select from the level 1 to level 8. Then press ENTER. The limitation will be more severe as the level number is lower.
4)Press OPEN/CLOSE to activate Parental control setting.
42
2K60121A.indb 42
1/12/2007 3:50:20 PM