Toshiba MV13P3 owner manual POWER-CORD Protection, Lightning, Power Lines, Overloading, Servicing

Page 4

IMPORTANT SAFEGUARDS (CONTINUED)

12.POWER-CORD PROTECTION

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.

13.LIGHTNING

To protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit due to lightning and power line surges.

14.POWER LINES

An outside antenna system should not be located in the vicinity of overhead power lines, other electric light or power circuits, or where it can fall onto or against such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact with them might be fatal.

15.OVERLOADING

Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.

16.OBJECT AND LIQUID ENTRY

Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.

17.OUTDOOR ANTENNA GROUNDING

If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded to provide some protection against voltage surges and built-up static charges, Section 810 of the National Electrical Code (NEC), ANSI/NFPA 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

18.SERVICING

Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

For example:

a.When the power-supply cord or plug is damaged.

b.If liquid has been spilled, or objects have fallen into the unit.

c.If the unit has been exposed to rain or water.

d.If the unit does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to its normal operation.

e.If the unit has been dropped or the cabinet has been damaged.

f . When the unit exhibits a distinct change in performance, this indicates a need for service.

19.REPLACEMENT PARTS

When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part.

Unauthorized substitutions may result in fire, electric shock or other hazards.

2

5L80301C P01-09

2

20/4/04, 16:25

Page 3 Page 5
Image 4
Page 3 Page 5
Contents TV/CABLE Mode Selection MV13P3Risk of Electric Shock Do not Open Cleaning AccessoriesPower Source Grounding or Polarization Read InstructionsPOWER-CORD Protection Power LinesReplacement Parts LightningHeat Safety CheckNEC Section Features Table of Contents Safety Precautions When YOU Experience the Above ConditionsMoisture Condensation Moisture will Condense on the Unit in the Following CasesTo USE AC Power Power SourceWider Hole and Blade AC Outlet Location of Controls Front RearDescription of Controls FrontCursor Selects an item in the menu Remote ControlSpeed button Sets the tape speed for recording Battery Installation Battery PrecautionsEffective Distance of the Remote Control FeetAntenna Connections JackOhm matching transformer Antenna Jack Combiner UHF 300 ohm VHF 300 ohmFor Subscribers to Scrambled Cable TV Service For Subscribers to Basic Cable TV ServiceCable TV Connections Starting Setup EnterSetting the Language Auto Clock Setting Auto Clock SettingAuto Clock Adjustment To SET Auto Clock to OFFAuto for automatic setting read EDS in the signal Press MENU. Press Bor a to select optionPress or to select Daylight Saving TIME, then press a Menu screen is clearedManual Clock Setting Press Bor Ato setMonth, then press As in , then pressPress Power Adjust the volume level byTV Operation Cable TV ChannelsCall MuteChannel + MuteClosed Caption Channel Return SleepSleep Closed CaptionClosed Captioning with a VCR What is Closed CAPTIONING?To View Closed Captions To Memorize Channels Cable TV chartTV/CABLE Selection Then press a Automatic Memory TuningNumbers will remain red until auto memorizing is complete To ADD/DELETE Channels Channel selectionSetting the V-CHIP To Register PasswordEnter the same password Using Direct channelTo SET the V-CHIP Enter To use the TV after the TV is protectedTo Change Password To SET the on Timer Press B or Ato select ON/OFF TIMER, thenOn TIMER, then press a Option Press aPress Bor Ato select To SET the OFF TimerOption Press a Cancel Picture Control AdjustmentsSelection Pressing Adjusting the Picture Preference Mode Picture QualityPress B or a to select option PREFERENCE, then press a Press or to select the desired pictureAutomatic Power on and Play Loading and Unloading a Video CassetteLoading UnloadingTape Speed and Maximum PLAYBACK/RECORDING Time To Prevent Accidental Erasure To Record AgainSP Standard Play Playback To Start PlaybackStop To Stop PlaybackDigital Tracking Controls REWTo Rewind or Forward the Tape Rapidly FORWARD/REVERSE Picture SearchSpecial Playback StopSkip Search PAUSE/STILLTo Watch a Tape Repeatedly Over until the repeat mode is canceledPress Bor Ato select on Recording a TV Program Recording and Viewing the Same TV ProgramScreen and the REC indicator will light To Stop Recording To Stop Recording TemporarilyPress Direct channel selection 0-9orCH + Ple ChannelONE-TOUCH Timer Recording OTR Press Direct channelTimer Recording Press or to select Timer REC SETPosition, then press Enter Press the or to select the programTimer REC indicator will light Speed as in stepPress Enter Steps 3 to 6 to set the second programOther Functions for the Timer Recording CancelTo Cancel a Program If the Program ProgramTo View the Counter Display Using the Real Time Tape CounterDisplay the elapsed time Using Zero Return Before playback or recording, press000000 Press Zero ReturnTo Monitor a TV Program TV MonitorIndex search Connection to Another VCR Duplicating a Video TapeConnection to Camcorder Reception Disturbances Problem and Troubleshooting Guide Check the following chart before requesting serviceSymptom Cause Possible Solution Power No powerSymptom Cause Possible Solution Remote ControlDepressed To turn on the closed caption RecordingVideo Head Cleaning Video Head CleaningVideo Head Clogging TelevisionLimited Ninety 90 Day Warranty Limited One 1 Year WarrantyLimited Two 2 Year Warranty of Picture Tube Rental UnitsHow to Obtain Warranty Service Toll FreeContinental United States contact 04/04 U
Top Page Image Contents