Toshiba D-VR17KB owner manual Timer Recording

E9GA0BD_EN.book Page 33 Monday, March 26, 2007 11:06 AM

Timer Recording

Video	VR
DVD-RW	DVD-RW DVD-R DVD+RW

DVD+R VCR

You can set the unit to record up to 12 programmes, up to a month in advance. Daily or weekly programme recordings are also available.

•Be sure to set the clock before entering a timer programming.

Insert a recordable disc or a tape with a record tab.

1 In stop mode, press [TIMER PROG]. Timer Programming list will appear.

2 Select “New Program” using [U / D], then press [ENTER].

Timer Programming

0:00 THU 06/12

Date Start End CH PDC

06/12 7:00 9:00 P10

07/12	9:00	9:30	P08
	New Program

1/1

•If there are 7 programmes or more, use [SKIP B / F] to turn the page.

3 Enter the date using [U / D], then press [P].

Each time you press [D] at the current date, the timer recording date will change as follows.

e.g., 1st January

01/01
Daily
M-F (Mon.-Fri.)
W-SAT
W-FRI
W-SUN
31/01
Timer Programming
		0:00 THU06/12
Date	Start	End	CH
01/01	--:--	--:--	P01
REC To	Mode	PDC
DVD	SPNew ProgramOFF
		SP	2:00
			1/1

4 Enter the time to start and to end

using [U / D], then press [P].

5 Select the channel number to record using [U / D], then press [P].

To record from the external input, select “AV1”, “AV2”, or “AV3”.

6 Select the recording media (“DVD” or “VCR”) using [U / D], then press [P].

7 Select the recording mode using [U / D], then press [P].

Refer to “Recording Mode” on page 26 for DVD or page 72 for VCR.

8 Select “PDC” to “ON” or “OFF” using [U / D].

Refer to “PDC (Programme Delivery Control)” on page 34.

9 Press [ENTER] when all information required is entered.

Your programme setting is stored.

•To set another programme, repeat steps 2 to 9.

•To exit, press [TIMER PROG].

•When 2 or more programmes are overlapped, “Timer program overlapped” appears, and the overlapped programme will be displayed in blue. To correct the timer Programme, Refer To “Checking, Cancelling or Correcting the Timer Programming Information” on page 34.

10 Press [TIMER SET].

Timer Programming

0:00 THU 06/12

Date	Start	End	CH PDC
06/12	7:00	9:00	P10
07/12	9:00	9:30	P08
07/12	17:00	18:00	P08
	New Program

1/1

The icon will appear on the front panel display and the unit enters to the timer-standby mode.

Note

•If you have not set the clock, the clock setting window will appear instead of the Timer Programming list. Continue from step 4 in “Manual Clock Setting” on page 25 before programming the timer.

•Use [L / P] to move the cursor to the left and the right in the entry screen for the timer programming.

•If a basic recording or One-touch Timer Recording is in progress on one component (e.g. VCR) and the timer recording set for the other component (e.g. DVD) is about to begin, the unit automatically switches to the programmed channel for timer recording 2 minutes before the programmed starting time, and the recording in progress (for VCR) will be cancelled UNLESS their recording channels are the same. If their recording channels are the same, the timer recording will start without cancelling the recording currently in progress. In this case, the recording of the same channel will be made on both DVD and VCR.

EN 33

Introduction Connections Basic Setup Recording Playback

Editing Function Setup VCR Functions Others