Toshiba 42XV500A, 37XV500A, 46XV500A owner manual Using REGZA-LINK

Page 26

Using the TV’s features (General)

Using REGZA-LINK

This feature uses CEC (Consumer Electronics Controls) technology and allows the control of Toshiba REGZA-LINK compatible devices from the TV remote control via HDMI connection (- page 39).

Note:

Not all Toshiba products currently support REGZA-LINK.

REGZA-LINK one touch play

When connected device is turn on REGZA-LINK will automatically detect the TV through the input selection. If the TV is in standby it will be turn on automatically. This feature is selected in the REGZA-LINKsetup menu.

Note:

Even if the device is showing a menu the TV may automatically show the video input source on-screen display.

REGZA-LINK system standby

This feature automatically turns the connected device into standby when the TV goes into standby and conversely for the TV to switch into standby when connected device goes into standby.

REGZA-LINK system audio control

Using the Speaker Preference feature allows the TV remote control to adjust the volume or mute the sound of the speakers connected to the TV via an AV amplifier.

Ensure that the connected AV amplifier and REGZA-LINK device are selected in the input source selection and that the Speaker Preference is set to Amplifier in the REGZA- LINK setup menu.

Notes:

•When you turn on the AV amplifier, change its input source, or adjust the sound volume, the sound will be output from the AV amplifier’s speakers even if the TV Speakers has been selected. Turn the TV to standby and on again to output the sound from the TV’s speaker.

•The proper function may not work by operating AV Amplifier.

Note:

The above functions are dependent on the connected device and TV setting.

REGZA-LINK functions

When the Enable REGZA-LINKis set to On, it allows the following functions to be enabled by setting them to On.

TV Auto Input Switch

If a connected HDMI device displays an OSD menu or starts playing video or audio, the TV will automatically switch to the appropriate HDMI input.

TV Auto Power

If a REGZA-LINK device is turned on or off, the TV turns on or standby automatically.

Auto Standby

If the TV is set to standby, the TV will send a message to turn off the selected REGZA-LINK device connected to the TV.

Speaker Preference

From this item, you can set your audio output preference to the TV speakers or the AV amplifier speakers. When this item is set to Amplifier, the TV remote control can be used to adjust or mute the volume of the audio. This item will be greyed out unless a REGZA-LINK compatible AV amplifier is connected.

Notes:

•When you turn on the AV amplifier, change its input source, or adjust the sound volume, the sound will be output from the AV amplifier’s speakers even if TV Speakers has been selected. Turn the TV to standby and on again to output the sound from the TV’s speakers.

•The above functions are dependent on the connected device and TV setting.

To set the REGZA-LINK set up

1Press M and ￿ or ￿ to select the REGZA-LINKmenu.

REGZA-LINK

Enable REGZA-LINK

On

 

 

TV Auto Input Switch

On

 

 

TV Auto Power

On

 

 

Auto Standby

On

 

 

Speaker Preference

TV Speakers

MENU Back EXIT Watch TV

2Press ￿ or ￿ to select Enable REGZA-LINK, then press ￿ or ￿ to select On.

Note:

If you set Enable REGZA-LINKto Off, the all other items will be greyed out.

3Press ￿ or ￿to select the REGZA-LINK set up item you want to use, and press ￿ or ￿ to select On/Off or the desired speakers mode.

•TV Auto Input Switch: On/Off

•TV Auto Power: On/Off

•Auto Standby: On/Off

•Speaker Preference: TV Speakers/Amplifier/

Off (See details on the previous page.)

REGZA-LINK input source selection

When any devices using CEC technology has connected, REGZA-LINK icon shows on the input source list.

o:

DTV

o1

o2

o3

HDMI1

HDMI2 REGZA-LINK

HDMI3

PC

ATV

To select the REGZA-LINK input source, refer to “Selecting the video input source to view” on page 25.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents 37XV500A 42XV500A 46XV500A Contents Introduction Important Safety InstructionsInstallation Welcome to ToshibaHigh temperatures can melt plastic and lead to fires Precautions for moving the TVPrecautions for installing on outdoor aerial UseYou may suffer an electric shock ServiceIf the TV is still power used in this condition, it may Never repair, modify or disassemble the TV by yourselfCleaning Important informationGetting started Connecting an aerialInstalling the remote control batteries Exploring your new TVTV front and side panel controls HDMI3 input terminal High-DefinitionDigital Audio Coaxial output terminal TV back panel connectionsDigital Audio Optical output terminal Learning about the remote control Location of controlsLocation of controls for REGZA-LINK mode Switching off the TV Tuning the TV for the first timeSwitching on the TV Turning the TV onThis menu will display only Digital TV selected Displaying the Digital Setting chartDisplaying the TV Setup menu chart At this point you can rescan the signal or refer to Enabled, Password menu will be displayed. EnterWhich is the default password If problem persistsManually setting channels in the channel memory Programming channels automaticallyWatching TV programmes Dolby D Setting the Time FormatSorting programme position -analog only Press to select the new position 4, then pressSelecting the picture size Using the TV’s features GeneralPicture adjustment Resetting the picture position analog only Using the picture stillAdjusting the picture position analog only Activating picture preferencesAdjusting the film stabilization Setting the black/white levelUsing the cinema mode Using Activating the ClearFrameSound adjustment Using the SRS WOW surround sound Selecting the dual 1 or dual 2 modeAdjusting the sound quality Mono modeOther feature settings Press or to select Mode and or to choose Off Programme Timer digital onlySetting the Alarm digital only To delete a selected entryEx. PC VGA mode Setting the sleep timerSetting the manual setting menu analog only Selecting the video input source to viewUsing REGZA-LINK Teletext in Analog TV Setting up the teletext modeUsing Auto mode To control the REGZA-LINK deviceUsing List mode Teletext in Digital TVPassword Other Digital TV features and settingsSetting the EPG Electronic Password StatusParental rate Setting the parental rateSetting favorite, locking and skipping channels Channel listRestore Factory Setting, then press Q Favorite ModeRestore factory setting SubtitleTransparency TV SetupAudio Preference Back connections Connecting your TVConnecting an audio system digital only Connection exampleConnecting an amplifier equipped with an Mpeg decoder Side connectionsConnecting a DVI device Connecting an Hdmi deviceConnecting an Hdmi or a DVI device Hdmi type a connector-to-DVI adapter cableSelecting the Hdmi setting Setting the HDMI1 audio modeSelecting the AV output mode To connect a PC to the RGB/PC terminal on the TV Connecting a computerFollowing signals can be displayed To connect a PC to the Hdmi terminal on the TVAdjusting the sampling clock Using the PC settingAdjusting the picture size/position Resetting the PC settingTV back view AV Amplifier REGZA-LINK connectionBefore controlling the devices Playback deviceSymptom and solution digital only TroubleshootingSymptom and solution Reference sectionAustralian Parental Guidance Codes Normative Programme Timer and/or Alarm do not operate properlyForget Password Please contact to the local dealerBroadcast transmission systems of each country or region SpecificationsBroadcast system Integrated Digital LCD TV37XV500A 94.0 cm 42XV500A 106.7 cm 46XV500A 116.8 cm Temperature 35 C HumidityPAL, SECAM, Ntsc 3.58/4.43 Dots 5 1,080 V dotsYC/J
Top Page Image Contents