Toshiba 43A61 owner manual Using the Remote Control

Page 14

Using the Remote Control

Programming the remote control for use with a non-Toshiba VCR or a cable TV converter

The TV remote control is preprogrammed to operate Toshiba VCRs and cable TV converters.

To use the remote control to operate a non-Toshiba VCR or cable converter:

1.Refer to the VCR and Cable TV converter code tables on pages 15Ð16 to find the corresponding code for your VCR or converter.

If more than one code is listed, try each one separately until you find the one that works.

2.If you are programming the remote control to operate your:

¥VCR, set the TV/CABLE/VCR switch on the remote control to VCR.

¥Cable converter, set the TV/CABLE/VCR switch on the remote control to CABLE.

3.While holding down RECALL, press the Channel Number buttons (0Ð9) to enter the code for your brand of VCR or converter.

4.Point the remote control at the VCR or converter and press POWER to test the code.

If the VCR or converter responds, you have entered the correct code.

If the VCR or converter does not respond to the remote control, you may have entered the wrong code. Repeat steps 1Ð4 using another code.

5.To control the TV, set the TV/CABLE/VCR switch to TV.

For future reference, write down the codes you used:

VCR code

_____________________

Cable TV converter code

_____________________

 

LIGHT RECALL POWER

RECALL

 

 

TV

 

 

 

POWER

 

 

 

 

CABLE

MUTE TV/VIDEO TIMER

 

VCR

 

 

 

TV/CABLE/

 

 

 

 

1

2

3

 

VCR Switch

 

Channel yz

4

5

6

CH

 

Channel

7

8

9

 

 

Numbers

 

 

CH RTN

VOL

 

 

 

100

0

ENT

 

Enter

 

 

 

 

 

 

ADV/

 

 

.CAPT

PIP CH

MENU

 

 

 

 

C

 

 

 

 

FAV

ENTER

FAV

 

RESET

 

ADV/

EXIT

 

 

 

 

PIP CH

Note:

Every time you replace the batteries, you must reprogram the remote control.

Some newer VCRs are capable of working on either of two remote codes. These VCRs have a switch labeled “VCR1/VCR2.” If your VCR has this kind of switch and does not respond to any of the codes for your VCR brand, set the switch to the other position (VCR1 or VCR2) and reprogram the remote control.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents 50A61, 50A62 Safety Precautions Dear CustomerImportant Safety Instructions InstallationService CareImportant Safety Information Introduction Exploring your new TV IntroductionWelcome to Toshiba Connecting your TV Connecting a VCRConnecting a cable converter box Connecting a cable converter box and a VCRConnecting a DVD player or satellite receiver and a VCR Two video cables One set of component video cablesConnecting two VCRs From AntennaConnecting a camcorder Connecting an audio systemConnecting an A/V receiver Connection example of Dolby Pro Logic surround systemInstalling the remote control batteries Using the remote controlPreparing the remote control for use Using the remote control with a VCR or a cable TV converterUsing the Remote Control VCR code table Brand name Code numberCable TV converter code table ABCLearning about the remote control Setting up your TV Press Exit to close an on-screen display instantlyPress x or to highlight your desired language Changing the on-screen display languageSelecting the antenna input Press z to select CH Program Adding channels to the TV’s memoryProgramming channels automatically Adding and erasing channels manually Changing channels using SpeedSurfChanging channels Press Exit twice to close the convergence menus Adjusting the color convergencePress x or to display the center convergence menu Switching between two channels Using the TV’s featuresAdjusting the channel settings Programming your favorite channelsUsing the TV’s Features Labeling channelsChannel Number Into the program block mode. See ÒUsing the V-CHIP menuÓ on Watching picture-in-picture PIPFreezing the small picture Switching the main and small picturesChanging the position of the small picture Entering the PIN code If you cannot remember your PIN codeChanging the PIN code Using the V-CHIP menu TV Rating Independent rating system for broadcastersLocks menu Mpaa Rating Independent rating system for moviesMovie ratings you can lock are described as follows From the Locks menu, selectLocking channels Unlocking programs temporarilyTo unlock the front panel buttons Select OFF in above Locking video inputsLocking the front panel buttons To adjust the picture quality Adjusting the pictureAdjusting the picture quality Selecting the picture modesTo turn off the flesh tone feature Highlight OFF in above Using the flesh tone featureUsing the noise reduction feature Saving new preferencesSelecting the color temperature Resetting your picture adjustmentsWatching video input Selecting the video input labelsTo turn off the closed-caption feature, highlight OFF Using the closed caption featureClosed caption feature has two options To view text, highlight T1, T2, T3, or T4Press Enter to start the timer Setting the sleep timerSetting the clock To display the time on-screen Press RecallSelecting stereo/SAP broadcasts Adjusting the soundMuting the sound Using the surround sound feature Adjusting the sound quality Resetting your audio adjustmentsTo turn off the SBS Highlight OFF in above Using the sub-bass system SBSTurning off the built-in speakers To turn on the built-in speakers Highlight on in aboveSelecting the Audio OUT sound Using the StableSound featureTo turn off the StableSound feature Highlight OFF in above Displaying on-screen information Viewing the demonstration modeSelecting the background of the menu display Understanding the auto power off feature Understanding the last mode memory featureSpecifications AppendixTroubleshooting Limited United States Warranty Limited Canada Warranty Appendix Index Channel programmingManufactured by
Top Page Image Contents