Toshiba 43A61 Adjusting the color convergence, Press x or to display the center convergence menu

Page 22

Adjusting the color convergence

This projection TV uses three separate TV tubes: red, green, and blue. The red, green, and blue images are projected onto the screen where they converge to form a full-color picture. You can see a clear picture only when the three images converge correctly. Convergence can drift over time or if you move the TV. If you can see clear images on your TV screen, skip this procedure.

Make this adjustment only after the TV has been on for at least 30 minutes.

To check and adjust the color convergence:

1.Press MENU, and then press x or • until the PICTURE menu appears.

2.Press y or z to highlight CONVERGENCE.

P I CTURE ANTENNA

MODESPORTS

FLESH TONE	ON
NO I SE REDUCTION	OFF
COLOR	COOL
TEMPERATURE	COOL
CONVERGENCE

SAVE NEW PREFERENCE

3. Press x or • to display the center convergence menu.

LIGHT RECALL POWER

TV

CABLE MUTE TV/VIDEO TIMER VCR

1	2	3
			CH
4	5	6
7	8	9
		CH RTN	VOL
100	0	ENT
		ADV/
.CAPT	PIP CH		MENU
.CAPT			MENU
C
FAV	ENTER		FAV
RESET		ADV/	EXIT
		ADV/	EXIT

PIP CH

Number

MENU

ENTER

yzx •

EXIT

Setting up your TV





	RED	BLUE
	ENTER : TO SELECT					COLOR
	EX I T : TO		SELECT			POS I T I ON

If you see separate color lines (red, blue, and green or white), you need to adjust the convergence.

4.Press ENTER to highlight RED or BLUE.

5.Press y (up), z (down), x (left), or • (right) to converge the red or blue line into the green (or white) line. When the convergence is adjusted correctly, you will see two single, crossed white lines.

6.Press EXIT to display the circumference convergence menu.

7.Press the corresponding Number button (1–4 and 6–9) to select the area of the screen you want to adjust.

8.Press ENTER to highlight RED or BLUE.


	1						2				3

	4										6
	4										6

		PUSH		1 – 9

	7						8				9



		RED			BLUE
		ENTER : TO SELECT					COLOR
		EX I T : TO SELECT					POS I T I ON

9.Press yzx • to converge the red or blue line into the green (or white) line.

Repeat steps 8 and 9 until you see two single, crossed white lines.

10.Press EXIT once to select another area to adjust in the circumference convergence menu, and then repeat steps 7–9.

11.Press EXIT twice to close the convergence menus.

22

Image 22

Contents 50A61, 50A62 Safety Precautions Dear CustomerImportant Safety Instructions InstallationService CareImportant Safety Information Introduction Welcome to Toshiba IntroductionExploring your new TV Connecting your TV Connecting a VCRConnecting a cable converter box Connecting a cable converter box and a VCRConnecting a DVD player or satellite receiver and a VCR Two video cables One set of component video cablesConnecting two VCRs From AntennaConnecting a camcorder Connecting an audio systemConnecting an A/V receiver Connection example of Dolby Pro Logic surround systemInstalling the remote control batteries Using the remote controlPreparing the remote control for use Using the remote control with a VCR or a cable TV converterUsing the Remote Control VCR code table Brand name Code numberCable TV converter code table ABCLearning about the remote control Setting up your TV Press Exit to close an on-screen display instantlySelecting the antenna input Changing the on-screen display languagePress x or to highlight your desired language Programming channels automatically Adding channels to the TV’s memoryPress z to select CH Program Changing channels Changing channels using SpeedSurfAdding and erasing channels manually Press x or to display the center convergence menu Adjusting the color convergencePress Exit twice to close the convergence menus Switching between two channels Using the TV’s featuresAdjusting the channel settings Programming your favorite channelsUsing the TV’s Features Labeling channelsChannel Number Into the program block mode. See ÒUsing the V-CHIP menuÓ on Watching picture-in-picture PIPChanging the position of the small picture Switching the main and small picturesFreezing the small picture Changing the PIN code If you cannot remember your PIN codeEntering the PIN code Using the V-CHIP menu TV Rating Independent rating system for broadcastersLocks menu Mpaa Rating Independent rating system for moviesMovie ratings you can lock are described as follows From the Locks menu, selectLocking channels Unlocking programs temporarilyLocking the front panel buttons Locking video inputsTo unlock the front panel buttons Select OFF in above To adjust the picture quality Adjusting the pictureAdjusting the picture quality Selecting the picture modesTo turn off the flesh tone feature Highlight OFF in above Using the flesh tone featureUsing the noise reduction feature Saving new preferencesSelecting the color temperature Resetting your picture adjustmentsWatching video input Selecting the video input labelsTo turn off the closed-caption feature, highlight OFF Using the closed caption featureClosed caption feature has two options To view text, highlight T1, T2, T3, or T4Press Enter to start the timer Setting the sleep timerSetting the clock To display the time on-screen Press RecallMuting the sound Adjusting the soundSelecting stereo/SAP broadcasts Using the surround sound feature Adjusting the sound quality Resetting your audio adjustmentsTo turn off the SBS Highlight OFF in above Using the sub-bass system SBSTurning off the built-in speakers To turn on the built-in speakers Highlight on in aboveTo turn off the StableSound feature Highlight OFF in above Using the StableSound featureSelecting the Audio OUT sound Selecting the background of the menu display Viewing the demonstration modeDisplaying on-screen information Understanding the auto power off feature Understanding the last mode memory featureSpecifications AppendixTroubleshooting Limited United States Warranty Limited Canada Warranty Appendix Index Channel programmingManufactured by