Toshiba 20HL85 appendix Ventilation

Page 4

Introduction

9. VENTILATION

Slots and openings in the cabinet back or bottom are provided for ventilation, and to

ensure reliable operation of the unit, and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the unit on a bed, sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heat source. This unit should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

10.POWER SOURCE

This unit should be operated only from the type of power source indicated on the rating plate. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company.

Wide plug

11. GROUNDING OR POLARIZATION

This unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet.

12. POWER-CORD PROTECTION

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.

13. LIGHTNING

To protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit due to lightning and power line surges.

14. POWER LINES

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall onto or against such power lines or

circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact with them might be fatal.

15.OVERLOADING

Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.

16.OBJECT AND LIQUID ENTRY

Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.

17.OUTDOOR ANTENNA GROUNDING

If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded to provide some protection against voltage surges and built-up static charges, Section 810 of the National Electrical Code (NEC), ANSI/NFPA 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

EXAMPLE OF ANTENNA GROUNDING AS PER THE NATIONAL ELECTRICAL CODE

NEC-NATIONAL ELECTRICAL CODE

S2898A

ANTENNA LEAD IN WIRE

GROUND

CLAMP

ANTENNA DISCHARGE UNIT

(NEC SECTION 810-20)

ELECTRIC SERVICE

EQUIPMENT GROUNDING CONDUCTORS

(NEC SECTION 810-21)

POWER SERVICE GROUNDING

GROUND CLAMPS

ELECTRODE SYSTEM (NEC ART 250, PART H)

 

4

J3U70101C(E)P02-10

4

15/06/2005, 4:10 PM

Image 4
Contents TV’s Features Your TVIntroduction Dear CustomerFCC compliance information AppendixFederal Communications Commission FCC FCC Declaration of Conformity Compliance Statement PartVentilation Introduction Connecting your TV Setting up your TV Using the TV’s Features AppendixHeat LCDPrecautions ScrewConnecting your TV Power sourceSetting up your TV Using the TV’s featuresExploring your new TV Selecting a location for the TV Connecting a VCRStereo VCR Option 1 For Subscribers to Basic Cable TV Service Connecting a cable converter box or antennaOption 2 For Subscribers to Scrambled Cable TV Service Connecting a DVD player/satellite receiver and a VCR DVD player with Component video From DTV Antenna Connecting a camcorder Connecting an Hdmi or a DVI device to the Hdmi input ’s FeaturesTo connect an Hdmi device, you will need To connect a DVI device, you will needConnecting a PC Personal Computer Power connectionTo use AC power Monitor Display modesInstalling the remote control batteries Preparing the remote control for useUsing the remote control to operate your other devices Programming the remote control to operate your other devices To control a DVD playerSetting up Your TV Using the TV’s Features AppendixSetting Up your TVLearning about the remote control Starting setup Changing the on-screen display languageTo select a language PressAdding channels to the TV’s memory Programming channels automaticallyAdding and erasing channels manually Changing channelsSwitching between two channels Adjusting the channel settingsProgramming your favorite channels Using the Locks menu Selecting a passwordTo select your password and access the Locks menu To change your passwordUsing the V-Chip parental control feature Locking channels Setting the GameTimerTM Using the panel lock featureTo create channel labels Labeling channelsTo erase channel labels Setting the clock Selecting the video input sourceLabeling the video input sources To label the video input sourcesSetting up your TV Using the TV’s Features Setting the on timerTo cancel the on timer Selecting the picture size Natural picture sizeTheaterWide picture size for 43 format programs Full picture size for 169 source programsSelecting the cinema mode Using the Aspect featureTo set the Cinema Mode to Film To set the Cinema Mode to Video offSetting the sleep timer Using the closed caption featureAdjusting the picture Selecting the picture modeAdjusting the picture quality Connecting your TV SettingUsing the CableClear feature Selecting the color temperatureResetting your picture adjustments TV’sAdjusting the sound Adjusting the sound qualityMuting the sound Selecting stereo/SAP broadcastsUsing the StableSound feature Resetting your audio adjustmentsUsing the WOW surround sound feature Adjusting the back lighting feature Auto power offUnderstanding the Power Return feature Selecting the Hdmi audio input sourceResetting your picture/audio adjustments in the PC mode Picture/Audio adjustments in the PC modePicture menu Troubleshooting Symptom SolutionSpecifications VHF UHFLimited United States Warranty Limited Canada Warranty TV’s Features Appendix MemoMemo Memo National Service Division