Silvercrest KH 2159 manual Code learn function, Delete All programmed buttons

Page 21

4.The memory can accommodate 150 button commands.

If the memory is full the LCD display q shows "LEARN FULL" and the learn mode will end.

5.With the EXIT button y you return to the previous status (except with a notice of "LEARN KEY" and/or "LEARN- ING").

Code learn function

1.Press the device button e for the device that the URC should learn a button code.

2.Hold down the S button r for a little longer than 3 sec- onds. The notice "CODE SETUP" appears.

3.With the  or  button t select the menu "LEARN SETUP" and then press the OK button l.

4.In the LCD display q "LEARN SET" appears. Then press the OK button l. In the LCD display q "LEARN KEY" ap- pears.

5.First press the button on the URC that is to be taught. In the LCD display q "LEARNING" appears. The URC now waits for the infrared signal from the original remote control.

Note:

Should the notice not change to "LEARNING" you have selected a button for which no button code can be taught.

6.Point the infrared sensors 2) of both remote controls towards each other.

7.Now hold down the desired button of the original remote control until "SUCCESS" or "LEARN ERROR" appears in the display q of the URC.

8.If in the LCD display q "SUCCESS" appears (process successful), you can teach further buttons begining with step 5. If "LEARN ERROR" appears (process unsuccessful) repeat the process in any case from step 5.

9.To stop the learning process press, during the display “LEARN SET”, repeatedly the EXIT button y until the standard display is show in the LCD display q. During the notice "LEARN KEY" and/or "LEARNING" simply al- low 30 seconds to pass without any operation then the device will end the menu.

Delete All programmed buttons

1.Hold down the S button r for a little longer than 3 sec- onds. The notice "CODE SETUP" appears.

2.With the  or  button t select the menu "LEARN SETUP" and then press the OK button l. In the LCD display q "LEARN SET" appears.

3.With the  or  button t select "LEARN CLEAR"

(taught delete) and confirm with the OK button l. In the LCD display q "CONFIRM CLEAR" (confirm delete) appears.

4.Confirm with the OK button l. In the LCD display q "SUCCESS" appears. All programmed buttons are de- leted. Finally the menu will automatically end.

- 19 -

Image 21

Contents 10-in-1 Remote Control Page Index Important safety instructions Device summary Initial useImportant safety instructions To high temperaturesDevice at a future date VOL +/- buttons k Menu button l OK button FAV / EPG button Device summaryUnpacking the device/checking the package contents Initial useInserting the batteries LCD display Operating componentsALL OFF button. w ButtonsButton r Number buttons oButton for one/two digit programme numbers a Stop Playback/Record/Wind RecordPause playback RewindSetup System settings Page Code Setup Programming the remote control Programming by brand code search= a = D = G = J = M = P = T Programming by automatic code search Programming by manual code inputTips Setting the time System-SetupSetting the date OK button l Display the year 2010 blinks. With the  orSetting the global volume/mute switching Adjust contrastBackground Illumination You can set the displays contrast as follows Setting the lock function System reset Timer SetupSleep timer Event timerBy pressing a button on the URC Learn SetupDelete All programmed buttons Code learn functionOK button l Macro Setup= Pause time = Execute a Macro Favourites channelPress the Macro button To delete all MacrosRepeat the steps to apply further favourites Vol +/-, Mute switching Volume controlFor operation All OFFFaults / Remedies Cleaning and storageDisposal Technical dataImporter Warranty & ServiceProgrammering pr. mærke-kode-søgning IndholdsfortegnelseAnvendelsesområde Vigtige sikkerhedsanvisningerBelysningstaste Oversigt over fjernbetjeningenIbrugtagning Udpakning/kontrol af fjernbetjeningenIndsætning af batterier LCD-display BetjeningselementerTaster Page Stop for afspilning/optagelse/spoling OptagelseStands afspilning Spoling tilbageSetup systemindstillinger Page Programmering pr. mærke-kode-søgning Code Setup programmering af fjernbetjeningenProgrammering pr. automatisk kodesøgning Programmering pr. manuel kode-indtastningBemærk Indstilling af klokkeslæt Indstilling af datoLCD-displayet q viser klokkeslættet. Sådan indstiller du Indstilling af kontrast BaggrundsbelysningIndstilling af global lydstyrke/mute Indstilling af låsefunktionen System-resetHændelses-timer Sleep-timerLern Setup Kode-indlæringsfunktion Makro Setup Programmering af makroKræfter med OK-tasten l Tryk på MACRO-tasten FavoritkanalVol +/-, muteindstilling Indstilling af lydstyrkeGentag trinene for at oprette flere favoritkanaler Åbning af favoritkanalerRengøring og opbevaring Vedrørende betjeningenSluk alt Med tastenLCD-displayet q viser ikke noget Fejl / afhjælpningBortskaffelse Tekniske dataInfo om overensstemmelse Importør Garanti & serviceUniversal Remote Control KH Atori Cimline Galaxi Kaisui Nokia Royal LUX Uher LCD TV Denzel DVD-DVR Denko Migros DTV Setup Box Satellite Discoverer Houstion Packsat Redpoint SAT-DVR DVR Receiver Page