Silvercrest Universal Remote Control Programming and Code Setup Guide

Page 13

Code Setup (Programming the remote control)

3 Programming methods are available for the remote control: Programming by brand code search, by automatic code search and by direct code input (manual).

First you should use the brand code search since this method is the fastest way of programming if the manufacturer of your de- vice is itemized in the code list. As second is recommended the direct code input followed by the automatic code search.

Programming by brand code search

With this method you select the brand and code direct via the LCD display q.

Observe the following operational references to programme the remote control:

1.Press the device button e for the device that you want to programme the remote control.

2.Hold down the S button r for a little longer than 3 sec- onds. Carry out entries in the menu quickly because after approx. 15 seconds without an entry the menu will be ended.

3.In the LCD display q "CODE SETUP" appears. Press the OK button l. "ENTER CODE" now appears in the LCD display q. With the  buttons t select "BRAND

CODE" and confirm with the OK button l.

4.Now appears the alphabetical first brand name from the list of pre-programmed devices.

5.With the 34 buttons t select the various brand names.

6.To make access easier you can skip directly to specific let- ters of the alphabet with the number buttons o:

2

=> A

3

=> D

4

=> G

5

=> J

6

=> M

7

=> P

8

=> T

9

=> W

Example With button number 5 the display skips to the letter "J". The first brand is "JVC"*. If, for example, you own a "Kenwood"* brand device, continue leafing with the 4 button t until this brand name appears. (* All brand names used here are trademarks of the corre- sponding manufacturer.)

7.The majority of manufacturers use several different codes for the remote control. You must now ascertain which of the available codes is best suited to your device. On the right underneath the brand name the relevent code will be shown in the LCD display q.

8.Point the remote control to the relevent device and press the function buttons to test the code (except 4t, OK l, EXIT y, or the number buttons o).

- 11 -

Image 13
Contents 10-in-1 Remote Control Page Index Important safety instructions Device summary Initial useTo high temperatures Important safety instructionsDevice at a future date VOL +/- buttons k Menu button l OK button FAV / EPG button Device summaryInitial use Unpacking the device/checking the package contentsInserting the batteries LCD display Operating componentsALL OFF button. w ButtonsNumber buttons o Button rButton for one/two digit programme numbers a Stop Playback/Record/Wind RecordPause playback RewindSetup System settings Page Programming by brand code search Code Setup Programming the remote control= a = D = G = J = M = P = T Programming by automatic code search Programming by manual code inputTips Setting the time System-SetupSetting the date OK button l Display the year 2010 blinks. With the  orSetting the global volume/mute switching Adjust contrastBackground Illumination You can set the displays contrast as followsSetting the lock function System reset Timer SetupSleep timer Event timerBy pressing a button on the URC Learn SetupDelete All programmed buttons Code learn functionOK button l Macro Setup= Pause time = Execute a Macro Favourites channelPress the Macro button To delete all MacrosRepeat the steps to apply further favourites Vol +/-, Mute switching Volume controlFor operation All OFFFaults / Remedies Cleaning and storageDisposal Technical dataImporter Warranty & ServiceProgrammering pr. mærke-kode-søgning IndholdsfortegnelseAnvendelsesområde Vigtige sikkerhedsanvisningerBelysningstaste Oversigt over fjernbetjeningenUdpakning/kontrol af fjernbetjeningen IbrugtagningIndsætning af batterier LCD-display BetjeningselementerTaster Page Stop for afspilning/optagelse/spoling OptagelseStands afspilning Spoling tilbageSetup systemindstillinger Page Programmering pr. mærke-kode-søgning Code Setup programmering af fjernbetjeningenProgrammering pr. automatisk kodesøgning Programmering pr. manuel kode-indtastningBemærk Indstilling af dato Indstilling af klokkeslætLCD-displayet q viser klokkeslættet. Sådan indstiller du Baggrundsbelysning Indstilling af kontrastIndstilling af global lydstyrke/mute Indstilling af låsefunktionen System-resetHændelses-timer Sleep-timerLern Setup Kode-indlæringsfunktion Programmering af makro Makro SetupKræfter med OK-tasten l Tryk på MACRO-tasten FavoritkanalVol +/-, muteindstilling Indstilling af lydstyrkeGentag trinene for at oprette flere favoritkanaler Åbning af favoritkanalerRengøring og opbevaring Vedrørende betjeningenSluk alt Med tastenLCD-displayet q viser ikke noget Fejl / afhjælpningTekniske data BortskaffelseInfo om overensstemmelse Importør Garanti & serviceUniversal Remote Control KH Atori Cimline Galaxi Kaisui Nokia Royal LUX Uher LCD TV Denzel DVD-DVR Denko Migros DTV Setup Box Satellite Discoverer Houstion Packsat Redpoint SAT-DVR DVR Receiver Page