Plasmon LF 6602 user manual Setting the Scsi ID, Setting the BUS Parity Checking

Page 57

SETTING THE SCSI ID

The SCSI ID can be set to one of eight device Identification (ID) numbers (0 through 7); however, each device connected to the same SCSI bus must have a different SCSI ID.

Perform the following procedure to set the LF 6600's SCSI ID number:

1)Enter the Configuration mode by pressing both the LOAD/MENU and TEST/SELECT switches simultaneously.

2)Press the MENU switch until "Set Config" is displayed.

3)Press the SELECT switch to enter the Set Configuration menu.

4)Press the MENU switch until "SCSI ID" is displayed.

5)Press the SELECT switch to scroll through the options for the SCSI ID value (0,1,2,3,4,5,6,7). When the desired value is displayed for the SCSI ID, press MENU to enter the SCSI ID value and move to the next option in the Set Configuration menu.

6)Simultaneously press the LOAD/MENU and TEST/SELECT switches to exit the Configuration mode. Simultaneously press the LOAD/MENU and TEST/SELECT Switches again to move up to the Main menu.

NOTE

After resetting the device ID, turn the drive off, wait 1 sec and then turn the drive on again. This ensures that the new device ID will be acknowledged by the SCSI bus.

SETTING THE BUS PARITY CHECKING

SCSI bus parity generation is always enabled; however, SCSI bus parity checking at the drive can be disabled.

Perform the following procedure to turn parity checking on or off.

1)Enter the Configuration mode by pressing both the LOAD/MENU and TEST/SELECT switches simultaneously.

2)Press the MENU switch until "Set Config" is displayed.

3)Press the SELECT switch to enter the Set Configuration menu.

4)Press the MENU switch until "Parity:" is displayed.

5)Press the SELECT switch to scroll through the states for parity checking (on, off) When the desired state is displayed, press MENU to enter the state and move to the next option in the Set Configuration menu.

6)Simultaneously press the LOAD/MENU and TEST/SELECT switches to exit the Configuration mode. Simultaneously press the LOAD/MENU and TEST/SELECT Switches again to move up to the Main menu.

97654438 E Page 57

Image 57

Contents Optical Disk Drive Page Page Warnung Agency Compliance and Approval Page Table of Contents Accessories Appendix a Related Publications ScopePage General Description Page Front Panel Drive CharacteristicsRear Panel Dimensions and Weight Temperature TEMPERATURE, Humidity and AltitudeShock and Vibration AC Power RequirementsTilt Range AC Power CordHeat Dissipation Particulate LimitsLocation of LF 6600 Warning Labels Page Unpacking the LF Unpacking and Repacking InstructionsUnpacking the LF Removing Banding Straps from LF EP005017 Positioning Ramp on Pallet Moving the Shuttle to the Home Position Repacking the LF Inspecting the LFShipping Bracket on Rear of LF 6602 Cabinet Manually Closing the Drives Baseplates Moving the Shuttle Assembly to the Shipping Position Page Page Installation Requirements InstallationScsi BUS Considerations Terminator LF 6602-to-Host Cable Connection Connecting Power and Scsi Cabling SINGLE-DEVICE Configuration Connector Verification MULTIPLE-DEVICE ConfigurationExtension Procedures LF 6602 Cabinet Configuration Showing Interlock Location Page Operating Instructions Controls and IndicatorsTEST/SELECT POWER-ON Procedure Modes of Operation Operating ModeOperating Condition DOC Display English French German Viewing the configuration View Config Configuration ModePage Main Menu View Configuration Messages Viewing the Configuration View ConfigDisplay HW Page Page Scsi ID Rd Ahead Setting the BUS Parity Checking Setting the Scsi IDSetting the Write Protect Option Setting the LanguageSetting the Load Switch Option Setting the Media Autoload OptionSetting the CDE Curs Option Setting the Read Ahead OptionSetting the Modsel RA Option Setting the Busy OptionSetting the MM Spinup Option Clear NvRAM Diagnostics Selftests Clear Rtpm Diagnostics Menu Part SET the Internal Drive Serial Number SET Serial # Page DRV SN Test Mode Media Cartridge Handling Page Setting the Write Protection Switch Media Access Door Media Insertion and RemovalAffixing Labels LF 6600 Media Access Cartridge Insertion Cartridge Removal Opening the Baseplates Manual Cartridge Release MechanismRemoving the Bezel Back View of Bezel Retracting the Cartridge Media Loading Accessing Drives Operator MaintenanceTrim Panel Label Interlock Inspecting and Cleaning FAN and Blower Filters Replacing Fuses Media Cleaning Using Cleaning KIT P/N Media CleaningPage Plasmon AccessoriesProduct Part Type Connector a Connector B Description Number Table below list the optional media cleaning accessories Page German Translations / Übersetzungen INS Deutsche Appendix aAbmessungen UND Gewicht TEMPERATUR, Luftfeuchtigkeit UND SeehöheWechselstrombedarf Stoss UND VibrationKipptoleranz WechselstromerdungWärmeausstrahlung WarnhinweiseAuspachen DER LF Wiederverpacken DES LFWarnung Installationsanforderungen ANSCHLUßÜBERPRÜFUNG Einstellen DIE Deice ID EinschaltverfahrenHandhabung VON Datenträgerkassetten Auswechseln VON Sicherungen Warnung