OPPO Digital DV-987HD user manual T U P M E N U O P T I O N S

Page 46

S E T U P M E N U O P T I O N S

•Press the left/right ARROW buttons to select the channel to be adjusted.

•Press the up/down ARROW buttons to raise or lower the volume of the selected channel in 0.5dB increments.

•Press the SELECT button to confirm the settings and return to the Audio Setup Page.

Channel trim is generally not required since most A/V receivers have the capability to adjust channel trim and compensate for speaker sensitivity differences. However if your receiver does not have such functions, you may adjust channel trim on the DVD player. For most accurate results, it is recommended that you use test tones from a calibration disc, such as AVIA Guide to Home Theater, and a SPL (Sound Pressure Level) meter.

7.Audio Delay: To add delay to analog or PCM digital audio output. If you experience audio/video synchronization problem, you may use this option to add a slight delay to the audio so it is in-sync with video.

•Press the left/right ARROW buttons to adjust delay. The audio delay can be adjusted in 10ms steps.

•Audio delay does not apply to raw bit stream digital audio output.

8.HDMI Audio: To select digital audio output from the HDMI port. The options are:

•LPCM – Digital audio output via HDMI will be multi-channel Linear PCM format. The Down- mix setting in the “Speaker Setup Page” will affect whether and how multi-channel audio content will be down-mixed to stereo. When this option is selected, compressed audio bit streams will decoded by the DVD player. This setting is recommended when connecting the HDMI output directly to a TV.

•Auto – Digital audio output via HDMI will be the same as the digital coaxial/optical audio output for CD, Dolby Digital and DTS audio signals. For high resolution stereo or multi- channel audio contents such as DVD-Audio and Super Audio CD, the DVD player will send multi-channel PCM audio signals with the highest available sample frequency and bit numbers. Depending on the original audio content, the format could be 44.1kHz - 192kHz, 2 - 6 channels. This option is recommended when connecting the HDMI output to an A/V receiver or processor with HDMI 1.1 or above audio capabilities.

•Off – No digital audio output via HDMI.

NOTE

If you use HDMI to connect audio to an HDMI A/V receiver or audio processor, it is recommended that you choose 720p or higher HDMI output resolution when playing high resolution audio content (DVD-Audio and SACD). According to the HDMI specification, the bandwidth available for audio is proportional to the total bandwidth used by video. At 480p/576p resolution, the HDMI specification can only support 2 channels of audio with high sample rate (up to 192kHz), or 8 channels of audio with standard sample rate (up to 48kHz). Depending on the capability of your A/V receiver or audio processor, if you play high resolution audio content at 480p/576p resolution, you may get reduced audio resolution, incomplete audio channels, or even no audio/video output at all. Choosing a high HDMI output resolution such as 720p or 1080i allows enough bandwidth for all high sample rate audio channels.

42

Page 45 Page 47
Image 46
Page 45 Page 47
Contents DVD Player Page Table of Contents Setup Menu Options Important Information Important Safety Instructions Additional Safety InstructionsFCC Statement Trademarks Type Size Recorded ContentsCopyright Protection Compatible Disc TypesFront Panel Controls Rear Panel ConnectorsFront Panel Display Window PLAY/PAUSE Button Start or pause playback Remote ControlKeyboard Button Show/hide virtual keyboard Battery Installation Using the Remote ControlMaking the Video Connection Hdmi ConnectionDVI Connection Connecting to an Audio System Connecting to a Receiver/Amplifier with Hdmi Input/OutputConnecting to a Receiver/Amplifier with 5.1ch Audio Input Installation Connecting to a Stereo or Surround Audio System Setup Menu Name Menu Item Submenu Item or Selection Setting Up the Player Initial SetupUse the Setup Menu System PreferenceCCS Determine Your Display Type Select the Best Output Resolution Audio Connection Directly to TV Set up Audio OptionsMulti-Channel Digital Audio to Receiver through Hdmi Multi-Channel Analog Audio to Receiver Set the Speaker Setup Page Down-mix to 5.1CHCoaxial or Optical Digital Audio to Receiver Stereo Analog Audio to Receiver Disc Playback Pause PlaybackDVD Menu Playback Volume ControlMute Audio Language/Channel Selection OSD On-Screen DisplaySubtitle Selection Angle Selection Zooming the Displayed FrameSound Field and EQ Mode Adjustment Power Spectrum Meter PSMTV System Selection Fast PlaybackRepeat Playback Slow PlaybackRepeat the Selected Section Playback from a Specific Location Random and Shuffle PlaybackPlayback by Track Number DVD discsTrack time search CD discsDisc time search Select a trackMemory and Automatic Resume BookmarksViewing Static Pictures on DVD-Audio Discs Virtual KeyboardDisc Browser Playing DivX, Digital Audio and Picture FilesDigital Music Play Operations Digital Picture Play Operations Playing a Disc with Both Digital Audio and Picture FilesSetup Menu Options General SetupT U P M E N U O P T I O N S Speaker Setup T U P M E N U O P T I O N S T U P M E N U O P T I O N S Audio Setup T U P M E N U O P T I O N S T U P M E N U O P T I O N S Video Setup T U P M E N U O P T I O N S Preference T U P M E N U O P T I O N S Troubleshooting Useful NotesSpecifications CD-R/RW, DVD±R/RW, DVD+R DLLanguage Code List Code Language NameLimited Warranty Oppo Digital, Inc. Limited One Year WarrantyM I T E D W a R R a N T Y
Top Page Image Contents