OPPO Digital DV-983H user manual Hdmi Button

Page 28

I N S T A L L A T I O N

3. Turn on the DVD player with no disc in its tray, or if the DVD player is already on, make sure that playback is completely stopped.

4. Press the HDMI button to show the current output resolution. Each subsequent press of the HDMI button switches the output resolution in the following sequence:

HDMI Button

NTSC output via HDMI:

480p Æ 720p 60Hz Æ 1080i 60Hz Æ 1080p 60Hz Æ Back to 480p again

PAL output via HDMI:

576p Æ 720p 50Hz Æ 1080i 50Hz Æ 1080p 50Hz Æ Back to 576p again

NTSC output via component (HDMI not connected and “Primary Output” set to “Component”):

480i Æ 480p Æ 720p 60Hz Æ 1080i 60Hz Æ 1080p 60Hz Æ Back to 480i again

PAL output via component (HDMI not connected and “Primary Output” set to “Component”):

576i Æ 576p Æ 720p 50Hz Æ 1080i 50Hz Æ 1080p 50Hz Æ Back to 576i again

NTSC output via component (HDMI connected or “Primary Output” set to “HDMI”):

480i only (The displayed information is for HDMI and does not reflect the component output)

PAL output via component (HDMI connected or “Primary Output” set to “HDMI”):

576i only (The displayed information is for HDMI and does not reflect the component output)

5.The selected output resolution will be briefly displayed on the upper left corner of the TV screen as well as on the DVD player’s front panel display.

6.The currently selected output resolution is also indicated by the front panel resolution indicators.

NOTE

•Some TV sets do not support one or more output resolutions (particularly 1080p). In this case repeatedly press the HDMI button until a supported resolution is selected. Give your display a second or two to “grab on” to the new signal and attempt to display a picture.

•In case you are not able to get a picture using the HDMI or component output, please connect the DVD player to the TV using either the composite video or S-Video output, and then use the setup menu to adjust the DVD player settings.

•Video up-conversion over the component output is only available for unencrypted discs such as home video and consumer-created contents. Most commercially pressed DVD discs are CSS-encrypted and will be limited to 480i/480p resolution. This restriction applies to the component output only. The HDMI output is protected with HDCP and has no such restriction.

•The Consumer Electronics Association (CEA) has not published a standard for 1080p component video signal yet. There are very few TV models on the market that support 1080p over component. OPPO cannot guarantee that the 1080p component output from the DVD player will be compatible with your TV or display device.

22

Page 27 Page 29
Image 28
Page 27 Page 29
Contents DVD Player Page Table of Contents Setup Menu Options Iii Page Important Information Important Safety Instructions Additional Safety InstructionsFCC Statement Type Size Recorded Contents Copyright ProtectionTrademarks Compatible Disc TypesFront Panel Controls Front Panel Display WindowRear Panel Connectors Volume Decrease volume Remote ControlVolume + Increase volume Battery Installation Using the Remote ControlMaking the Video Connection Hdmi ConnectionDVI Connection Hdmi DVIComponent Video Connection Connecting to an Audio System Connecting to a Receiver/Amplifier with Hdmi Input/OutputConnecting to a Receiver/Amplifier with 7.1ch Audio Input Connecting to a Receiver/Amplifier with 5.1ch Audio Input Receiver/Amplifier with Dolby Digital or DTS Decoder Connecting to a Stereo or Surround Audio System Infrared Remote IR Installation Custom Installation OptionsRS232 Control Setting Up the Player Initial Setup Use the Setup Menu SystemSetup Menu Name Menu Item Submenu Item or Selection PreferenceMulti-Channel Determine Your Display Type Select the Best Output Resolution HdmiHdmi Button Audio Connection Directly to TV Set up Audio OptionsMulti-Channel Digital Audio to Receiver through Hdmi Multi-Channel Analog Audio to Receiver Set the Speaker Setup Page Down-mix to 7.1CH or 5.1CHCoaxial or Optical Digital Audio to Receiver Stereo Analog Audio to Receiver LT/RTDisc Playback DVD Menu PlaybackPause Playback OSD On-Screen DisplayVolume Control MuteAudio Language/Channel Selection Subtitle SelectionAngle Selection Zooming and Aspect Ratio Control TV System SelectionZoom Levels for Hdmi Output V a N C E D O P E R a T I O N S V a N C E D O P E R a T I O N S Zoom Levels for Component Video Output Slow Playback Fast PlaybackRepeat, Random and Shuffle Playback Repeat the Selected Section CD disc Sacd discPlayback by Track Number Playback from a Specific LocationCD discs Sacd discsTrack time search Disc time searchSelect a track Bookmarks Memory and Automatic ResumeViewing Static Pictures on DVD-Audio Discs Disc Information BrowserPlaying Digital Video, Audio and Picture Files Digital Music Play Operations Digital Picture Play OperationsUse of USB Device Playing a Disc with Both Digital Audio and Picture FilesAudio-Only Mode Customized Background ScreenSetup Menu Options General SetupT U P M E N U O P T I O N S T U P M E N U O P T I O N S Speaker Setup 12 ft Settings Channel Trim To set the volume of each individual channel Audio Setup Mode Dolby Digital Setup Dual Mono Video Setup T U P M E N U O P T I O N S T U P M E N U O P T I O N S Preference Old Password New Password Confirm Password Troubleshooting Useful NotesSpecifications Language Code List Code Language NameLimited Warranty Oppo Digital, Inc. Limited One Year WarrantyM I T E D W a R R a N T Y
Top Page Image Contents