REFERENCES
Useful Notes
•In order to prolong the service life of your DVD player, it is recommended to wait at least 30 seconds before you turn it on again after switching it off.
•Remove disc and turn power off after operation.
•Some functions of the player may not be applicable to certain discs.
•Some discs with special features may not be fully supported by the player. This is not a malfunction of the unit.
•In case of player malfunctioning, please turn it off, wait for 30 seconds and turn it back on. If the problem still exists, please follow the troubleshooting instructions or contact an OPPO service center.
Troubleshooting
Use this chart to help you solve operational problems. If there are any problems that you cannot solve, please contact your OPPO service center.
| Symptom | Possible Cause | Solution | Reference |
|
|
|
| Page |
| No sound | Audio cable is not properly | Check audio cable, and then reconnect if necessary. | 9 - 16 |
|
| connected |
|
|
|
| Muting is activated | Press the MUTE button to cancel the mute. | 28 |
|
| SACD is played and the audio | This is not supported due to copyright restrictions of | 15 |
|
| connection is coaxial or optical | SACD. Please use the analog or HDMI audio output. |
|
|
| digital audio |
|
|
| No picture | Video cable is not properly | Check video cable, reconnect if necessary. | 9 - 10 |
|
| connected |
|
|
|
| TV input is not correctly | Select the input to which the DVD player is connected. |
|
|
| selected |
|
|
|
| Check the “A. Only” display on the front panel, and | 44 | |
|
|
| press the AUDIO ONLY button to cancel this mode. |
|
|
| Video output format is not | When playback is completely stopped, repeatedly | 21 |
|
| support by the TV | press the HDMI button until the picture appears. |
|
|
| Video system is not supported | When playback is completely stopped, press the P/N | 31, 58 |
|
| by the TV | button or set the correct TV Type. |
|
| No color | Video system is not supported | When playback is completely stopped, press the P/N | 31, 58 |
|
| by the TV | button or set the correct TV Type |
|
|
| Saturation set too low | Check the saturation setting on TV and DVD player. | 55 |
|
| Loose or damaged | If using | 9 |
|
| cable | properly plugged in and not damaged. |
|
|
| Incorrect video output port | If using composite video output, check that the cable is | 9 |
|
|
| not incorrectly plugged into the component video jack. |
|
| Incorrect color | Incorrect color space setting | If using HDMI for video output, check the color space | 55 |
|
|
| setting on the TV and DVD player. |
|
|
| Incorrect component video | If using component video output, check the three | 11 |
|
| cable connection | component video cables to make sure the signals |
|
|
|
| match on both ends |
|
| Picture rolling | Video system is not supported | When playback is completely stopped, press the P/N | 31, 58 |
|
| by the TV | button or set the correct TV Type |
|
| “No Disc” error | No disc or incompatible disc | Eject disc and check. | 26 |
|
| loaded in player |
|
|
|
| Disc not properly loaded | Eject disc and make sure the label side is facing up | 26 |
|
|
| and the record side is facing down. |
|
|
| Condensation on the Laser | Turn on the player, eject the disc and leave the player | 2 |
|
| on for about an hour. |
| |
| Remote control | Remote control is out of range | Use the remote control within the effective range. | 8 |
| failure | Low battery | Replace the batteries. | 8 |
60