Trouble-shooting

Many problems have a simple cause and a corres
pondingly simple solution. The following section de	s
cribes a few difficulties you may encounter, and th	e
measuresyouneedtotaketocurethem.

Ifyoufinditimpossibletosolveaproblemwitht hehelp ofthesenotes,pleasedisconnecttheunitfromthe mains andaskyourauthorised specialistdealerforadvice.

Problem:	Machine does not switch on (green
	LED stays dark).

Cause:	Mainsleadnotconnectedcorrectly.

Remedy:	Checkconnection,pushinfirmly.


Problem:	Machine does not respond when
	buttons are pressed.

Cause:	Static discharge or powerful interference
	(e.g.	lightning)	have affected the
	processor’smemory.

Remedy:	Reset	machine: disconnect the mains
	plug,waitabout 10seconds, thenplug in
	again.Switchthemachineon.


Problem:	Machine responds correctly when front
	panel buttons are pressed, but cannot
	be remote-controlled via an 'R' series
	pre-amplifier, integrated amplifier or
	receiver.

Cause 1:	Batteries in remote control handset
	exhaustedorfittedincorrectly.

Remedy:	Fit new batteries, or refit batteries with
	correctpolarity.

Cause 2:	RLINKor RCplugnotconnectedcorrectly
	tomachine’s RLINKor RCsocket.

Remedy:	Completeconnectionsasshowninwiring
	diagram;pushconnectorinfirmly.

Cause 3:	Novisualcontactbetweenremotecontrol
	transmitterandremotecontrolreceiver of
	the 'R' series preamplifier, integrated
	amplifierorreceiver.

Remedy:	Ensure direct visual contact between
	remote control transmitter and receiver
	(glassdoorsmaypreventcontact).
	Themaximumrangeoftheremotecontrol
	systemisabout8metres.
	Position the remote control receiver so
	thatitisnotsubjectedtodirectsunlightor
	excessively bright		lighting. Fluorescent
	lamps and energysaving bulbs are
	powerfulsourcesofinterference.

Cause 4:	TheDVDplayerisnotselectedascurrent
	listening source on the preamplifier,
	integrated amplifier or receiver, i.e. the
	control commands from the handset are
	being passed	to	another	'R' system
	device.

Remedy:	Press the (or  see next
	point)ontheremotecontrolhandset,and
	tryagain.

Cause:5:	The remote control address of the DVD
	player ( AUXor CD) does not correspond
	totheselectedaudioinputsocketsonthe
	preamplifier,	integrated		amplifier or
	receiver.

Remedy:	The' RLINK 2nd ADDR.'switchontheback
	panel can be used to configure the DVD
	player either as		AUX or	CD. You must
	then select the appropriate input sockets
	(see 'Back panel connections').


Problem:	Loud hum from the loudspeakers.

Cause:	Cinchplugsmakingpoorcontact,orfaulty
	Cinchlead.

Remedy:	Check all connections and connecting
	leadscarefully.


Problem:	No sound, or distorted sound.

Cause:	AudioconnectiontoamplifierorTVsetnot
	correct.

Remedy:	Completetheconnectionsasshowninthe
	wiringdiagram;pushconnectorsinfirmly.
	Selectadifferentlisteningsourcetocheck
	theamplifier.


Problem:	No sound signal via the digital output.

Cause 1:	Digitalplugnotconnectedcorrectlytothe
	digitaloutputsocketonthemachine.

Remedy:	Complete connections as per wiring
	diagram;pushconnectorsinfirmly.

Cause 2:	Digitaloutputswitchedoff.

Remedy:	Switch the digital output on using the
	SETUP menu.

Cause 3:	The data format of the selected audio
	channel(e.g.DolbyDigitalorDTS)isnot
	recognised by the decoder connected to
	thesystem.

Remedy:	Use a decoder which supports the data
	formats.