Arcam DV137 manual Using the CR-415 remote control, Disp display, RPT repeat

Using the CR-415 remote control

					0–9 keypad
	OPEN				This allows direct access to individual tracks on audio
					CDs. To select a track, press the corresponding keypad
	Opens and closes the disc tray				button followed by OK. For tracks greater than 9, enter
					the digits in sequence. For example, to play track 15,
					press 1, then 5, then OK.
	DISP (display)
	Dims or turns the DV137’s display on or off.		DVD
	Turning the display off generally gives a slight
	improvement in sound quality.					Standby
	Pressing DISP once turns the display off; twice
						Press Standby to toggle the standby state of the DVD
	dims the display. To restore the display to full
			1	2	3	player. Note that Arcam CD players are not controlled by
	brightness, press DISP a third time.	OPEN
						this button.
	A–B	DISP	4	5	6
	This button enables you to repeat a selected
	section from the disc (see page 20).	A–B	7	8	9
						CLEAR
	RPT (repeat)	RPT	CLEAR	0	PROG	Use CLEAR to clear a numeric field.
Press RPT to cycle through the repeat play options.
						Page Up/Down (DVD-audio)/
	Fast play and Skip chapter/tracks					Slow play (other discs)
						DVD-audio: Some DVD-audio discs allow the user to
Play fast (7 8) and Skip (0 /) chapters/tracks in
						browse through images (photographs of the artist, lyrics,
	both directions (see page 7).
						etc.) while music is being played. Use the ( or ) buttons
	SETUP	SETUP			MENU	to change to the previous/next page. Note that this is not
	‘Setup’ allows you to configure the DV137					availble on all DVD-audio discs.
	for use in your system. Ensure that no disc					Other discs: Press ( or ) on the remote control to play
	is playing and press SETUP to access the					slow forward or backwards. There are four speeds of
	‘Setup’ menu.					slow playback: 1/8, 1/6, 1/4 and 1/2. Press the button
			OK			repeatedly to cycle through the different speeds. To
						resume normal playback speed, press PLAY.
						Note that slow-play does not apply to audio CDs or DVD-
						audio discs.
						MENU
	Playback control					Press MENU to access the DVD ‘Disc’ menu.
	Pause (;), Play (4) and Stop (<)
						This navigation menu is specific to a disc and varies for
	(see page 7).
						each title, but typically offers facilities to select chapters,
						languages, and view extra material such as trailers or
						documentaries.
						Once the menu has been accessed, use the cursor pad to
		AUDIO	TRIM	TITLE	RTN	move around the menu and press OK to activate a menu
						‘button’.
	Advanced controls	ZOOM	ANGLE	SUBT	MODE	Cursor pad and OK button
	These buttons are described on the next page.
						Use the cursor pad to navigate the On-Screen Display
		RAND	STATUS	MEM	SRCH
						(OSD) and menu pages. Confirm your selection with the
						OK button.
						MUTE
						Stops sound to the speaker outputs of certain Arcam
						amplifiers.
						Volume +/–
			CR-415			Adjusts the volume on Arcam remote-controllable
						amplifiers.
						Note that the volume (+/–) controls and MUTE button
						have no effect on the audio output level of the DVD
						players.
	If the remote control receiver
	(located on the right of the front-
	panel window) is not ‘visible’ to the
	remote control hand-set, then the
	remote control will not work! Either
	locate the unit differently, or take
	advantage of the remote control
	input on the rear of the player
DV137	(consult your dealer for further
	information on this option).
E-10