Arcam DV137 manual Using the CR-515 remote control

Using the CR-515 remote control

DISP (display)	Standby
Dims or turns the DV137’s display on or off.	Press Standby to toggle the standby state of the DVD
Turning the display off generally gives a slight	player.
improvement in sound quality.

Pressing DISP once turns the display off; twice					HDMI
dims the display. To restore the display to full
brightness, press DISP a third time.					Selects the picture resolution for HDMI output.
*					CLEAR
					Use CLEAR to clear a numeric field.
Reserved for future use
					Page Up/Down (DVD-audio)/
	�		����	����	Slow play (other discs)
					DVD-audio: Some DVD-audio discs allow the user to
0–9 keypad	�		�	�	browse through images (photographs of the artist, lyrics,
					etc.) while music is being played. Use the 3 or 4 buttons
This allows direct access to individual tracks on audio
					to change to the previous/next page. Note that this is not
CDs. To select a track, press the corresponding keypad
	�		�	�	available on all DVD-audio discs.
button followed by OK. For tracks greater than 9, enter
					Other discs: Press 3 or 4 on the remote control to play
the digits in sequence. For example, to play track 15,
					slow forward or backwards. There are four speeds of
press 1, then 5, then OK.	�		�	�
					slow playback: 1/8, 1/6, 1/4 and 1/2. Press the button
					repeatedly to cycle through the different speeds. To
SRCH (search)	����		�	�����	resume normal playback speed, press PLAY.
Accesses the ‘Search’ menu to					Note that slow-play does not apply to audio CDs or DVD-
navigate to any point on the disc.					audio discs.
OPEN	����			������	STATUS
Opens and closes the disc tray					Press STATUS to give play status information about the
					current disc. Press STATUS again to close the status
Fast play and Skip chapter/tracks					display.
					The status information displayed varies depending on the
Play fast (7 8) and Skip (0 /) chapters/
					type of disc – DVD, CD or VCD.
tracks in both directions (see page 7).
			��		Cursor pad and OK button
					Use the cursor pad to navigate the On-Screen Display
SETUP					(OSD) and menu pages. Confirm your selection with the
					OK button.
‘Setup’ allows you to configure the DV137 for
					MENU
use in your system. Ensure no disc is playing and	�����			����
press SETUP to access the ‘Setup’ menu.					Press MENU to access the DVD ‘Disc’ menu.
Playback control					This navigation menu is specific to a disc and varies for
					each title, but typically offers facilities to select chapters,
Pause (;), Play (4) and Stop (<)
					languages, and view extra material such as trailers or
(see page 7).					documentaries.
					Once the menu has been accessed, use the cursor pad to
					move around the menu and press OK to activate a menu
	����	����	�����	���	‘button’.
Advanced controls					MUTE
	����	�����	����	�����	Stops sound to the speaker outputs of certain Arcam
These buttons are described on the next page.
					amplifiers.
	���	���	����	�����	Volume +/–
					Adjusts the volume on Arcam remote-controllable
					amplifiers.
					Note that the volume (+/–) controls and MUTE button
					have no effect on the audio output level of the DVD
		������			players.
					If the remote control receiver
					(located on the right of the front-
					panel window) is not ‘visible’ to the
					remote control hand-set, then the
					remote control will not work! Either
					locate the unit differently, or take
					advantage of the remote control
					input on the rear of the player
DV137					(consult your dealer for further
					information on this option).
E-8