Alpine IVA-D105 owner manual Set MX Mode of the External Audio Processor, Over Adjustment, 45-EN

Set MX Mode of the External Audio Processor

Before performing the operations below, set MX (Media Xpander) mode of the PXA-H700 to “AUTO” when the PXA-H700 is connected.

Setting item : MEDIA XPANDER

1 Select ON or OFF of MX by touching [ ] or [ ] of

MEDIA XPANDER.

OFF: Turns off the MX effect of every music source.

ON: Turns on the specified MX mode.

2 Touch [ ] after setting to ON.

The Media Xpander setup screen appears.

3 Touch [ ] or [ ] of the desired MX mode.

•Music source (such as radio broadcasts and CDs, excluding AM radio) level can be set.

MX CD (OFF, CD MX 1 to 3)

CD mode processes a large quantity of data. This data is used to reproduce the sound cleanly by making use of the data quantity.

MX CMPM (OFF, CMPM MX 1 to 3) / MX SAT (OFF, SAT MX 1 to 3)

This corrects information that was omitted at the time of compression. This reproduces a well-balanced sound close to the original.

MX FM (OFF, FM MX 1 to 3)

The medium to high frequencies become more clear, and produces well balanced sound in all the bands.

MX DVD (OFF, MOVIE MX 1 to 2)

The dialog portion of the video is reproduced more clearly.

(DVD MUSIC)

This disk contains a large quantity of data such as music clip. MX uses this data to reproduce the sound accurately.

MX AUX (OFF, CMPM MX, MOVIE MX, MUSIC MX)

Choose the MX mode (CMPM, MUSIC, or MOVIE) that corresponds to the media connected.

•The contents of MX set here is reflected to PXA-H700 or PXA-H701.

•When OFF is selected, MX effect of each MX mode will be OFF.

•Each music source, such as radio, CD, and MP3 can have its own MX setting.

•MX mode does not function when MX is ON for AM radio.

•MX CMPM is applied for MP3/WMA/AAC and iPod.

•MX SAT is applied for XM, SIRIUS, HD Radio.

•The MX setting can be performed only when a source is currently selected.

X-OVER Adjustment

Setting item : X-OVER

BassEngine

High pass filter can be applied to front/rear speakers, and low pass filter can be applied to the subwoofer.

1 Touch [ ] or [ ] of the speaker to make the desired adjustment.

•If you set the subwoofer LPF, set the front/rear HPF to OFF, or set the rear/front speaker to “LARGE” in “Speaker Setup” (page 48). The frequency you set for the subwoofer LPF will automatically be applied for the speaker that is set to “SMALL” for the HPF.

Therefore, certain frequencies may not be reproduced.

A.PROCESSOR

1 Touch [ ] or [ ] of X-OVER to select L/R or L+R.

L/R: Different adjustment values can be set for the left and right channels.

L+R: Sets the same adjustment values for the left and right channels.

The screen changes to the X-OVER screen to be adjusted.

4 Adjust the crossover to your preference.

Selecting the Cut-Off Frequency

Touch [ ] or [ ] of FREQ., then select the cut-off frequency (crossover point).

The adjustable bandwidth differs depending on the speaker (channel).

Adjusting the Level

Touch [ ] or [ ] of LEVEL, then adjust the HPF or LPF level.

Adjusting the Slope

Touch [ ] or [ ] of SLOPE, then adjust the HPF or LPF slope.

•When the speaker is set to the “OFF” mode, the X-OVER for that speaker cannot be set. Refer to “Setting the Speakers” (page 44).

•Check the playback frequencies of the connected speakers before adjusting.

•In order to protect the speakers, there is no OFF setting for the subwoofer low pass filter (the slope remains the same).

•The H.P.F. filter cannot be set to OFF (slope OFF) if Tweeter is selected for FRONT1 . Or, only the subwoofer is adjustable if STEREO is selected for the subwoofer.