Samsung SP43Q5 manual Becoming Familiar with the Remote Control, Button Viewing Function

Page 13

Becoming Familiar with the Remote Control

The remote control is used mainly to:

Change channels and adjust the volume

Set up the television using the on-screen menu system

The following table presents the most frequently used buttons and their functions.

Button

Viewing Function

Menu Function

 

Used to display the next

-

 

stored channel.

 

 

Used to display the

-

 

previous stored channel.

 

to Used to display the corresponding channels.

For double digit channels, the second digit must be pushed immediately after the first. Failure to do this will result in a single digit channel being displayed.

-/--Used to select a channel numbered ten or over. Press this button, and the -- symbol is displayed. Enter the two-digit channel number.

PRE-CHPress the PRE-CHbutton. The TV will switch to the last channel viewed.

To quickly switch between two channels that are far apart, tune to one channel, then use the numeric buttons to select second channel. Then, use the PRE-CHbutton to quickly alternate between them.

Used to increase the

-

volume.

 

Used to decrease the

-

volume.

 

MUTE Used to switch the sound off temporarily.

(

)

To turn the sound back on, press this button again, or

press the or button.

MENU

Used to display the

Used to return to the previous

(

)

on-screen menu system.

menu or normal viewing.

 

 

-

Used to:

 

 

 

Display a submenu

 

 

 

containing selections for

 

 

 

the current menu option.

 

 

 

Increase/decrease a

 

 

 

menu option value.

 

 

-

Used to confirm your choice.

TV/DTV

Used to switch between

-

 

 

TV and DTV mode.

 

EXIT

-

Used to exit from the any

(

)

 

display.

English - 13

Image 13
Contents Digital Television Page English Contents Symbols Control Panels depending on the model Side of the TV Inserting the Batteries in the Remote Control Infrared Remote Control Rear of the TV Connecting to an Aerial or Cable Television NetworkConnecting a Satellite Receiver or Decoder Placing Your Television in Standby Mode Switching Your Television On and OffPress the Power button on the remote control Mains lead is attached to the rear of your televisionButton Viewing Function Becoming Familiar with the Remote ControlStart Plug & Play Enter Return Setup Time Plug and Play FeatureIf you want to reset this feature Using the numeric 0~9 buttons Using the P ButtonsChanging Channels Choosing Your Language Displaying InformationIt can be displayed simply by pressing the Self Focus button Adjusting the Screen Automatically Self FocusDeactivating the Automatic Execution of the Self Focus Removing the Self Focus from the Display Press the D.MENU button Previewing the DTV Menu SystemChoosing Your Language You can set the translucency of the on-screen menu Adjusting the Translucency LevelUpdating the Channel List Automatically Bandwidth Channel Updating the Channel List ManuallyEditing Your Favourite Channels Preview MoveDelete Default PIN code for a new TV set is Setting up the Parental LockNow & Next Guide Viewing EPG Electronic Programme Guide InformationFull Guide ThenUsing the Scheduled List Using the Scheduled List You can preset the default guide style Setting the Default GuideViewing All Channels and Favourite Channels When the favourite channel list has not been set upSelect Yes You can change the colours for categories Selecting Category ColoursDisplaying Programme Information Viewing Channel ListsSubtitle Subtitle Language Audio Language Digital Text Using Your Preferred FeaturesYou can get information about the signal status Checking the Signal InformationViewing Product Information Upgrading the Software Option Upgrade NowViewing Common Interface Selecting the CI Menu Press the or button to select Reset. Press the Enter ResettingFreezing the Current Picture Press the EnterStoring Channels Automatically Not available in DTV or external input modeExchange of channel numbers by pressing the Enter button Sorting the Stored ChannelsAuto Storing Channels ManuallyChannel mode Skipping Unwanted Channels Assigning Names to Channels LNA Locking the ChannelIs displayed. P Fine Tuning Channel ReceptionButton then press the Enter button Using the LNA Low Noise Amplifier Feature Dynamic Standard Movie Custom Changing the Picture StandardTo select other options, press the or button Customizing the Picture SettingsPress the Menu button to return to the previous menu Reset function is set for each mode Dynamic, StandardSelecting the Picture Size Wide Model Analog Mode Signal Zoom Selecting the Picture Size Wide Model DTV ModeSignal Selecting the Scan Mode Setting the Digital NR Digital Noise Reduction Not available in DTV mode Setting the Blue ScreenStandard Music Movie Speech Custom Changing the Sound StandardAdjusting the Sound Settings Auto Volume Extra Sound SettingsDolby Virtual Setting the Melody Sound Selecting the Sound Mode depending on the model Setting and Displaying the Current Time Setting the Sleep Timer Auto Power Off Switching the Television On and Off AutomaticallyDTV Viewing an External Signal SourcePart Contents Teletext FeatureDisplaying the Teletext Information To activate the teletext mode and display the contentsTo display Press Selecting Display OptionsSelecting a Teletext Storing Teletext Pages depending on the model Video disc player Satellite receiver Decoder② Inserting the CI Common Interface card It is inactive when the card is improperly insertedCamcorder Video game device Video disc player Connecting to the RCA InputCamcorder Connecting to the S-Video InputConnecting to the Component Input Redirecting an Input to the External Output Ext.1 Default TVProgramming the Remote Control for Other Components Programming the Remote Control for Other Components Check the picture contrast and brightness settings Power buttonCheck the volume Normal picture but no sound Check the volumeAfter Sales Service