Samsung SP43Q5 manual Selecting the Picture Size Wide Model Analog Mode

Page 54

Selecting the Picture Size (Wide Model : Analog Mode)

TV	Picture
Mode	:	Dynamic	√
Size	:	Auto Wide	√
Scan Mode	:	Auto	√
Digital NR	:	Off	√
Move	Enter	Return

TV	Size
Auto Wide
16:9
Panorama
Zoom1
Zoom2
4:3
Cinema1
Cinema2
Move	Enter	Return

You can select the picture size which best corresponds to your viewing requirements.

1Press the MENU ( ) button.

Result : The main menu is displayed.

2Press the ▲ or ▼ button to select Picture.

Result : The options available in the Picture group are displayed.

3Press the ENTER ( ) button.

4Press the ▲ or ▼ button to select Size. Press the ENTER ( ) button.

Result : The Size menu is displayed.

5Select the required mode by pressing the ▲ or ▼ button. Press the ENTER ( ) button.

Result : The following modes are available:

Auto Wide Automatically enlarges the image to fit the 16:9 aspect ratio providing the optimum display.

16:9	Adjusts the picture to fit into the 16:9 wide aspect
	ratio.

Panorama	Adjusts a Wide picture to appear natural.

Zoom1	Vertically enlarges the picture approximately 130%.

Zoom2	Vertically enlarges the picture about approximately
	150%.

4:3	Adjusts the picture to fit into a 4:3 normal aspect
	ratio. (Prolonged use in 4:3 mode may cause the
	lifespan of the CRT to be reduced.)

Cinema1	To maintain optimum screen display, the picture is
	vertically enlarged and the letterboxed (black margin)
	area is filled with gray instead.

Cinema2	When the top and bottom of the screen margin are
	black (blank), they will change to gray.

➢◆ Lifting is available in the Zoom1 or Zoom2 mode by pressing the ▲ or ▼ button.

◆Subtitles may be cut-off or hidden below the screen area in Zoom1, Zoom2, Cinema1, and Cinema2 modes.

➢You can select these options by simply pressing the P.SIZE button on the remote control.

English - 54

Image 54

Contents Digital Television Page English Contents Symbols Control Panels depending on the model Side of the TV Inserting the Batteries in the Remote Control Infrared Remote Control Connecting to an Aerial or Cable Television Network Rear of the TVConnecting a Satellite Receiver or Decoder Press the Power button on the remote control Switching Your Television On and OffPlacing Your Television in Standby Mode Mains lead is attached to the rear of your televisionBecoming Familiar with the Remote Control Button Viewing FunctionPlug and Play Feature Start Plug & Play Enter Return Setup TimeIf you want to reset this feature Using the P Buttons Using the numeric 0~9 buttonsChanging Channels Displaying Information Choosing Your LanguageAdjusting the Screen Automatically Self Focus It can be displayed simply by pressing the Self Focus buttonDeactivating the Automatic Execution of the Self Focus Removing the Self Focus from the Display Previewing the DTV Menu System Press the D.MENU buttonChoosing Your Language Adjusting the Translucency Level You can set the translucency of the on-screen menuUpdating the Channel List Automatically Updating the Channel List Manually Bandwidth ChannelEditing Your Favourite Channels Move PreviewDelete Setting up the Parental Lock Default PIN code for a new TV set isFull Guide Viewing EPG Electronic Programme Guide InformationNow & Next Guide ThenUsing the Scheduled List Using the Scheduled List Setting the Default Guide You can preset the default guide styleWhen the favourite channel list has not been set up Viewing All Channels and Favourite ChannelsSelect Yes Selecting Category Colours You can change the colours for categoriesViewing Channel Lists Displaying Programme InformationUsing Your Preferred Features Subtitle Subtitle Language Audio Language Digital TextChecking the Signal Information You can get information about the signal statusViewing Product Information Upgrade Now Upgrading the Software OptionViewing Common Interface Selecting the CI Menu Freezing the Current Picture ResettingPress the or button to select Reset. Press the Enter Press the EnterNot available in DTV or external input mode Storing Channels AutomaticallySorting the Stored Channels Exchange of channel numbers by pressing the Enter buttonStoring Channels Manually AutoChannel mode Skipping Unwanted Channels Assigning Names to Channels Locking the Channel LNAFine Tuning Channel Reception Is displayed. PButton then press the Enter button Using the LNA Low Noise Amplifier Feature Changing the Picture Standard Dynamic Standard Movie CustomCustomizing the Picture Settings To select other options, press the or buttonReset function is set for each mode Dynamic, Standard Press the Menu button to return to the previous menuSelecting the Picture Size Wide Model Analog Mode Signal Selecting the Picture Size Wide Model DTV Mode ZoomSignal Selecting the Scan Mode Setting the Digital NR Digital Noise Reduction Setting the Blue Screen Not available in DTV modeChanging the Sound Standard Standard Music Movie Speech CustomAdjusting the Sound Settings Extra Sound Settings Auto VolumeDolby Virtual Setting the Melody Sound Selecting the Sound Mode depending on the model Setting and Displaying the Current Time Setting the Sleep Timer Switching the Television On and Off Automatically Auto Power OffViewing an External Signal Source DTVTeletext Feature Part ContentsTo activate the teletext mode and display the contents Displaying the Teletext InformationSelecting Display Options To display PressSelecting a Teletext Storing Teletext Pages depending on the model Decoder Video disc player Satellite receiverIt is inactive when the card is improperly inserted ② Inserting the CI Common Interface cardConnecting to the RCA Input Camcorder Video game device Video disc playerConnecting to the S-Video Input CamcorderConnecting to the Component Input Ext.1 Default TV Redirecting an Input to the External OutputProgramming the Remote Control for Other Components Programming the Remote Control for Other Components Check the volume Power buttonCheck the picture contrast and brightness settings Normal picture but no sound Check the volumeAfter Sales Service