Samsung CT-21D8L, CT-21S7W, CT-21D9W, CT-1488BL, CT-21D8W, CT-2188L manual Example Antenna Grounding

Page 4

Protect the power cord. Power supply cords should be routed so that they will not be walked on or pinched by items placed on or against them. Pay particular attention to cord placement at plugs, convenience receptacles, and at the point where they exit from the unit.

Unplug the TV receiver from the wall outlet and disconnect the antenna or cable system dur- ing a lightning storm or when left unattended and unused for long periods of time. This will prevent damage to the unit due to lightning and power-line surges.

An outside antenna system should not be placed in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits. Avoid overhead power lines: When installing an outside antenna system, be extremely careful to keep from touching the power lines or circuits. Contact with such lines might be fatal.

Do not overload the wall outlet or extension cords. Overloading can result in fire or electric shock.

Do not insert foreign objects through openings in the unit, as they may touch dangerous voltages or cause damage. Never spill liquid of any kind on the TV receiver.

Ground outdoor antennas. If an outside antenna or cable system is connected to the TV receiver, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Read information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna

discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

EXAMPLE OF

 

ANTENNA GROUNDING

ANTENNA

 

 

LEAD IN WIRE

GROUND CLAMP

 

 

ANTENNA

 

DISCHARGE UNIT

ELECTRIC

 

SERVICE

 

EQUIPMENT

GROUNDING

 

 

CONDUCTORS

 

GROUND CLAMPS

 

POWER SERVICE GROUNDING

 

ELECTRODE SYSTEM

Do not attempt to service the TV receiver yourself. Refer all servicing to qualified service personnel. Unplug the unit from the wall outlet and refer servicing to qualified service personnel under the following conditions:

-When the power-supply cord or plug is damaged

-If liquid has been spilled on the unit or if objects have fallen into the TV

-If the TV receiver has been exposed to rain or water

-If the TV receiver does not operate normally by following the operating instructions

-If the TV receiver has been dropped or the cabinet has been damaged

-When the TV receiver exhibits a distinct degradation in performance

If you make adjustments yourself, adjust only those controls that are covered by the operat- ing instructions. Adjusting other controls may result in damage and will often require exten- sive work by a qualified technician to restore the TV receiver to normal.

When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part. Unauthorized substitutions may result in additional damage to the unit.

Upon completion of any service or repairs to this TV receiver, ask the service technician to perform safety checks to determine that the TV receiver is in a safe operating condition.

2SAFETY

Image 4
Contents AA68-02343A-00 ENG CT-1488BL/CT-1488L/CT-14S7BLRisk of Electric Shock Do not Open Thank You for Choosing Samsung Example Antenna Grounding Your New TV InstallationOperation Special Features TroubleshootingList of Features Chapter OneFamiliarizing Yourself with The TV Video and Audio input jacks Rear Panel Jacks´ VHF/UHF Antenna terminal Remote Control ´ Number buttons+100 MTS OptionConnecting VHF and UHF Antennas Antennas with 300-ohm Flat Twin LeadsConnecting Cable TV Antennas with 75-ohm Round LeadsSeparate VHF and UHF Antennas Cable without a Cable BoxConnecting to a Cable Box that Descrambles Some Channels Connecting to a Cable Box that Descrambles All ChannelsConnect this cable to a two-way splitter Install AT I O N Connecting a VCR Unplug the cable or antenna from the back of the TVConnecting a Camcorder Installing Batteries in the Remote Control Press the Power button on the remote control Turning the TV On and OffViewing the Menus and On-Screen Displays Viewing the MenusSelecting a Menu Language Memorizing the Channels Selecting the Video Signal-sourceANT antenna STD, HRC or IRC all cable TV Storing Channels in Memory Automatic Method Adding and Erasing Channels Manual Method Press the VOL+ or VOL- button to select Added or ErasedAdjusting the Volume Changing ChannelsSetting the Clock Or CH button repeat Edly until the correct hour appearsCustomizing the Picture Press the Menu button to display the menuUsing Automatic Picture Settings Using Automatic Sound Settings Press the VOL+ or VOL- button Viewing a VCR or Camcorder TapePress the Menu button twice to exit Fine Tuning Channels Chapter FourChanging the Screen Size Using the Surf Feature Setting the On/Off Timer When finished, press VOL + button Setting the Sleep TimerPress the Sleep button on the remote control Sound Features Choosing a Multi-Channel Sound MTS Soundtrack OptionExtra sound settings Turbo Sound, or Surround SurroundViewing Closed Captions Identifying Problems Chapter FiveUsing Your TV in Another Country Cleaning and Maintaining Your TVSpecifications