Samsung HLN507W, HLN567W Front Panel LED Indicators, Rear Panel Jacks, Indicator Light Key

Page 8

BP68-00142A-1 5/27/03 10:09 AM Page 14

Your New Wide TV

Front Panel LED Indicators

The three lights on the front panel indicate the status of your TV.

Indicator Light Key

: Light is On

: Light is Blinking

Rear Panel Jacks

Use the rear panel jacks to connect components such as a VCR.

You can connect two different components such as two VCRs, Set-Top Box and a DVD player etc., because there are two sets of video input jacks and one set of component video input jacks on the rear panel of your TV. For more information, please see “Connections”.

: Light is Off

Timer

Lamp

Temp

Indication

Auto Timer ON/OFF has been set

Standby state.

The picture will automatically appear in about 25 seconds.

Auto Timer ON/OFF has been set and the set will automatically be turned on in about 25 seconds.

A cooling fan inside the set is not operating normally.

Lamp cover on rear of the set is not properly shut.

Check if the ventilation hole on the rear of the set is blocked, because if the inner temperature is too high, the power will shut off.

Lamp may be defective. Please contact a certified technician.

•It takes about 30 seconds for the TV to warm up, so normal brightness may not appear immediately.

•The TV has a fan to keep the inside lamp from overheating. You’ll occasionally hear it working.

ŒANTENNA terminals

Two independent cables or antennas can be connected to these termi- nals. Use ANT-A and ANT-B terminals to receive a signal from VHF/UHF antennas or your cable system. Use the ANT A-OUT termi- nal to send the signal being received by the ANT-A terminal out to another component (such as a Cable Set Top Box).

The PIP channel can be received only when a signal source is connected to ANT-A.

´S-VIDEO INPUT jacks

Connects an S-Video signal from an S-VHS VCR or DVD player.

ˇVIDEO/AUDIO INPUT jacks(VCR1, VCR2)

Connect video/audio signals from external sources, such as a VCR or DVD players.

¨VIDEO/AUDIO MONITOR OUTPUT jacks

Sends a video signal from the TV to an external source, such as a VCR.

Note: Monitor Out is available only in RF, Video and S-Video modes.

ˆComponent1 jacks (Y, Pb, Pr, L, R)

Use these jacks to connect the component video/audio signals from a DVD player when using the component video input jacks.

Note: Only 480i and 408p formats are supported.

ØComponent 2, 3 jacks (Y, Pb, Pr, L, R) Receives the DTV video/audio signals from a set top box. Note: Only 480p, 720p and 1080i formats are supported.

∏PC AUDIO INPUT jacks

Connect these to the audio-output jacks on your PC.

”DVI (Digital Video Interface) jack Receives the digital signals from a set top box or PC etc.

’RS-232C jack

˝PC VIDEO INPUT jack

Connect to the video output port on your PC.

14

15

Downloaded from www.Manualslib.com manuals search engine

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Dlptv Dlptv Thank You for Choosing Samsung Safety InstructionsImportant Safety Information M S U N G Table of Contents M S U N G Your New Wide TV Replacing the LampList of Features Side Panel ButtonsChecking Parts Side Panel JacksRear Panel Jacks Front Panel LED IndicatorsIndicator Light Key Remote Control Installing Batteries in the Remote ControlConnections Connecting VHF and UHF Antennas N n e c t i o n sAntennas with 300-ohm Flat Twin Leads Antennas with 75-ohm Round LeadsConnecting Cable TV and VCR Connecting a Cable Converter BoxConnecting a Cable Converter Box and a VCR Cable without a Cable BoxConnecting a Camcorder Connecting a DVD PlayerConnecting to Y,Pb,Pr Connecting to audio and video jacksConnecting a DTV Set Top Box Connecting to R,G,BConnecting to DVI Digital Visual InterfaceOperation E r a t i o n Turning the TV On and OffViewing the Menus and Displays Selecting the Menu LanguageChannel Memory Selecting the Broadcast SourceStoring Channels in Memory Automatically Adding and Erasing ChannelsChanging Channels Selecting Your Favorite ChannelsSetting The On/Off Melody Labeling the ChannelsCustomizing the Picture Using Automatic Standard Picture SettingsPicture Control Adjusting the Volume Using the Mute ButtonUsing AutomaticStandard Sound Settings Sound ControlSetting the On/Off Timer Setting the ClockSetting the Timers Viewing an External Signal Source Setting the Sleep TimerSelecting the Signal Source Remote Control VCR/DVD ButtonsSpecial Features Special Features Setting Up Your Remote ControlSetting Up the Remote to Operate Your VCR Setting Up the Remote to Operate Your Cable BoxDVD Codes Setting Up the Remote to Operate Your DVDVCR Codes Fine Tuning Channels Setting the Film ModeDNIe TM Digital Natural Image engine Digital Noise Reduction Setting the Blue Screen Mode Changing the Screen SizeMTS Settings Choosing a Soundtrack Special Audio OptionsDolby Virtual BBEClosed Captions Auto VolumeViewing Closed Caption Information Selecting a PIP Screen Selecting an External SignalViewing Picture-in-Picture Selecting a Signal Source Antenna or Cable for PIP Swapping the Contents of the PIP and Main imageChanging the Size of the PIP image Changing the Picture-in-Picture ChannelUsing the V-Chip Setting Up Your Personal ID Number PINSelecting the Sound Source Changing the Location of the PIP imageHow to Enable/Disable the V-Chip How to Set up Restrictions Using the TV guidelinesSpecial Features PC Display Using Your TV as a Computer PC Display How to connect Your PC to the TVHow to Set up Your PC Software Windows only D i s p l a yHow to Set up Your TV as a PC display Display ModesFine tuning Picture Quality AdjustmentFrequency Adjustment Changing the Screen Size PC mode Aspect Supported settingsWide TV Wide PCAppendix Troubleshooting Care and MaintenanceUsing the TV in Another Country SpecificationsM o
Top Page Image Contents