Samsung HG26NA477PF, HG46NA570LBXZA, HG46NA578LBXZA, 478, 470, HG40NA570LFXZA, HG40NA577LF Hdmi

Page 16

yy RJP (Remote Jack Pack): RJP stands for Remote Jack Pack. The RJP is a hardware module that has different Audio Video inputs (A/V, Audio, PC and HDMI) and corresponding outputs. The corresponding outputs are connected from the RJP to the TV. The RJP communicates with the TV via RS232. A Hot Plug & Play function allows hotel guests to connect an external source to the RJP. The RJP communicates with the TV by sending messages regarding Active/Inactive sources.

A group of menu items, RJP Priority AV, RJP Priority PC, and RJP Priority HDMI, let you assign numbered priorities to the jacks of the RJP. 1 is the highest priority and 3 is the lowest. When a guest connects external sources to the RJP jacks, the TV will automatically switch between sources based on the priority you have assigned them in the Menu. For example, lets say AV is set to 1 and HDMI to 2. If a guest has attached a device to the HDMI jack, and then plugs a device into the AV jack, the TV automatically switches to the device plugged into the AV jack (the jack with the higher priority). Note that a guest can also switch between devices manually by pushing a button on the RJP.

You connect the RJP to HDMI 1, 2, or 3 or AV 1 or 2.

When the TV is on, connect the TV and the RJP within 10 seconds.

yy The RJP can be returned to the factory default settings by pressing the A/V and HDMI buttons simultaneously for 10 seconds. All LEDs blink 5 times, acknowledging that the reset has been performed

yy The RJP will automatically turn off any LEDs after 5 minutes to avoid unnecessary light pollution in the hotel room. The LEDs that were turned off will turn on again if the guest touches any of the buttons and the 5 minute timer will restart. If the guest then touches another source button, the TV will change to the selected source and the corresponding LED will be lit.

yy After an RJP Reset or a TV Power OFF/ON, it takes approximately 10 seconds to establish communications between the TV and the RJP.

yy The following table shows the approximate time in seconds it takes to switch from the TV to an input source, based on assigned or default priorities.

Scenario 1: When no inputs are connected.

Source

To Connect

 

 

AV

2 Sec

PC

0.7 Sec

HDMI

3.9 Sec

Scenario 2: When two or more inputs are connected and an Input source is disconnected and then reconnected.

Source

Disconnect

To Connect

Total

 

 

 

 

AV

4.5 Sec

2 Sec

6.5 Sec

PC

0.7 Sec

0.7 Sec

1.4 Sec

HDMI

3.9 Sec

3.9 Sec

7.8 Sec

An example: If the RJP has all its live sources (AV, PC, and HDMI) connected, AV has been assigned the highest priority, the RJP is in HDMI mode, and a guest removes and reconnects the AV source, the minimum time required to switch to the AV source is 6.5 seconds.

yy To connect audio (Ipod or Mp3), Music mode should be ON. yy A/V, PC, and HDMI input sources are supported.

16 English

[HG470570 _HOTEL-ZA]ENG.indd 16

2012-04-17 �� 8:41:03

Image 16
Contents LED TV Serial NoSecuring the Installation Space IntroductionOperational Modes Still image warningContents Hotel Mount Kit AccessoriesYy Security Screws Bit tool sold separately English Installing the LED TV Stand Insert the Stand Guide into the slot on the bottom of the TVHotel Mount Kit Long Bolt 2EA Short Bolt 2EA Nut 2EA Washer 2EASwivel Assembling the swivel 32 inch TVs or largerUsing the TVs Controller Power is on Using the Function menuConnection Panel Component in / AV IN1 46 Model Component in / AVUSB / Cloning Remote Control Press to directly access channelsConnecting the TV to an SBB or STB TV Rear PanelVendor Cable code Pin assign Remark BN39-00865B ProvidedBN39-01011B NStreams BN39-01110A BN39-01011C LodgeNet MTI ProvidedLAN Model HG478/HG578 Connecting the Audio Output to an Audio AmplifierAudio Connecting the RJP Remote Jack Pack Hdmi Setting the Hotel Option Data Menu Items Enable or disable the Picture Menu Select the way to update clock dataMode It works normally Add a video signal, it works normallyDefault Popup window appears Ident and switch the input sourceLow Sets the TV to low energy saving mode SolutionInteractive remote controller for DTV that lets you deliver Off Only works Sirch Update on selected Sirch Update TimeUpgrade Sirch Clone / Binary by manual Select Sirch Update ChannelWelcome Message Hospitality Logo USB Cloning Failed Copy operation was not successfulNo USB USB is not connected Clone folder will be labeled T-MST4AUSCBHospitality Mode Power On Channel ENPower On Channel Power On Volume ENHdmi Music Mode USB Media ModeSub Amp Mode Sub Amp VolumeMulti Code Remocon Picture Menu Setting Auto InitializeSystem Menu Standalone mode Is set Interactive Hospital Option Menu TV will enter the RF Mode Press Power OFF To exitHotel Plug & Play Yy UI ScenarioHG470570 HOTEL-ZAENG.indd 2012-04-17 USB SW Upgrade Method Sound BarProduct TV size Vesa screw hole Standard Screw Installing the Wall Mount10~15 Anti-theft Kensington Lock Specifications Dimensions WxDxH BodyDimensions Unit inchesJack panel detail / Rear view 13.9 English29.3 27.5 15.5 16.5 18.3 20.6 19.0 EnglishHG40NA570 / HG40NA577 / HG40NA578 Front view / Side view 36.5 20.3 21.6 23.8HG46NA570 / HG46NA577 / HG46NA578 Front view / Side view 41.7 20.3 24.6 26.8HG32NA470 / HG32NA477 / HG32NA478 Samsung Electronics America, Inc License This page is intentionally Left blank HG470570 HOTEL-ZAENG.indd 2012-04-17
Related manuals
Manual 2 pages 6.03 Kb Manual 10 pages 31.03 Kb