Samsung PPM42S2 manual Main Screen, Beginning-Confirming the Port

Page 38

Main Screen

The program starts operating when entering the following sequence: Start ➔ Program ➔ Multiple Display Control.

Note : The remote control Enable/Disable function operates whether or not the power is On/Off. This applies to all the displays connected to the MDC. However, regardless of the status in which the MDC was shut down, the remote control signal receiving function of all the dis plays is initialized to Enable when the MDC is closed.

ŒMain icons : Click the main icons to switch into each screen.

´Display selection : Select a display from Display Selection by marking ‘v.’ ˇ Select button : Click Select All, Clear All to select or clear all displays.

¨ Info grid : Use Info Grid to see the brief information of selected display.

ˆ Control tools : Use Control Tools to control displays.

Ø Title : The current title to be controlled is displayed.

∏Remocon: It allows you to enable or disable the remote control signal receiving function of the display unit.

”Auto Adjustment : Adjusts the picture automatically.

Note : The Auto Adjustment feature operates only in Component2, RGB1, and RGB2.

Figure 3-1 Initial Screen

Warning

The remote control receiver’s Enable/Disable function operates despite whether the Power is On/Off. This applies to all displays connected to the MDC. However, all displays are initiated with the remote control receiver Enabled despite the status in which the MDC was shut off.

74

Beginning-Confirming the Port

The Multiple Display Control uses only Com1. This control operates with neither Com2 nor another port.

To check which port is installed, enter Control Panel ➔ Device Manager ➔ Ports.

If another port is installed except the “COM1” port, you can change to “COM1” from the “Device Manager” if you’re using Windows 2000 or XP (please refer to the follow- ing chapter). For all other operating systems, the change may be made from your PC BIOS Setup.

Use the Exit menu to end the program. The Help menu shows how to use the program and general information about the program.

Figure 3-2 Device Manager

75

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Owner’s Instructions Important Safety Information Thank You for Choosing SamsungFCC Information User InstructionsTable of Contents User InstructionsSetup Your New Plasma Display Panel Remote Control Buttons Installing the Display on the Wall Attachment Panel Wall Installation InstructionsInstallation Notes Wall attachment panelSeparating the Display from the Wall Attachment Panel Displaying Status Information Turning the MonitorPDP On and OffViewing the Menus and Displays Displaying ClockConnections Videotape Playback Connecting Speakers Connecting a VCR/Cable BoxConnecting speakers to stands Picture Control Connecting a DVD/Set-Top BoxPower Plug Video Y, Pb, Pr Cable Audio Cable To Play DVDPress the Menu button to exit Using Automatic Picture SettingsCustomizing the Picture Move the joystick left or right to change the valueViewing the Picture-in-Picture Selecting the PIP Screen Selecting an External SignalSource in the cover on the remote control Down to select PIP, then press the joystick toSelecting the Sound Source RGB mode Move the joystick up or down to select Locate Move the joystick to move the PIP screen where you WantMove the joystick up or down to select Size Move the joystick left or right to select Large or SmallFreezing the Picture When entering the Video modeChanging the Screen Size Sound Control Customizing the Sound Using Automatic Sound Settings Using the Surround Time SettingSetting the Clock Setting the Sleep TimerSetting the Timers Setting the On/Off TimerConnecting PC and Operation Setting up Your Monitor Plug and Play Connecting to a PCPin Configuration To watch the PC screenHow to Set up Your PC Software Windows only 848 X 60.000 29.800To enter Adjusting the PC ScreenAdjusting the R.G.B Press the joystick to enterEnlarging the Image Zoom Moving the Zoom Picture Changing the Size of the Image Picture Quality Adjustment Picture Automatic Adjustment On/OffFrequency Adjustment Fine Tuning PhaseHorizontal Sync Power Saver RGB mode onlyFunction Description Selecting a Menu Language Setting the Multi Control Numeric buttonsAuto Power On Digital Noise ReductionUsing the Panel Lock Setting up Your Remote ControlVCR Codes Cable Box Codes DVD Codes Remote Control CodesMultiple Display Control Installation IntroductionInstallation Continue Main Screen Beginning-Confirming the PortPower Control Beginning-Changing the PortSelection Screen of Power Control Input Source ControlSwitches the input source of the selected display into RGB2 Aspect Ratio Screen of Video/S-VideoTime Control Aspect Ratio Screen of RGB1, RGB2Settings Control-Picture Settings Control-Picture RGBSettings Control-Audio Settings Control Screen AudioTroubleshooting Appendix Care and Maintenance Specifications Memo
Top Page Image Contents