Samsung NC241T, NC190-T, NC191 Touch Screen, Enable right click on hold, Right click delay

Page 59

2Using "PCoIP"

Touch Screen

The Touch Screen page allows you to configure and calibrate certain settings of an attached Elo

TouchSystems touch screen display.

The Touch Screen page is only available through the OSD. It is not available in the Administrative Web

Interface.

Figure 2-23: Touch Screen

zEnable right click on hold

Select this checkbox to allow users to emulate a right-click when they touch the screen and hold it for a few seconds. If disabled, right-click is not supported.

zRight click delay

Slide the pointer to a position between Long and Short to determine how long a user must touch and hold the screen to emulate a right-click.

zTouch screen calibration

When you first connect the touch screen to the zero client, the calibration program will start. On the touch screen, touch each of the three targets as they appear.

To test the calibration, run your finger along the monitor and ensure that the cursor follows it. If it is not successful, the calibration program automatically restarts. Once calibrated, the coordinates are stored in flash.

To manually start the calibration program, from the OSD Touch Screen page, click Start. Follow the onscreen prompts.

2 Using "PCoIP" 59

Image 59
Contents NC191 NC241 Table Of Contents Connecting and Using 65 a Source Device Screen Setup Configuring Tint Resizing or Relocating the Screen Information Appendix Icons used in this manual Before Using the ProductSymbols for safety precautions CopyrightCleaning CleaningPrecautions for storage Securing the Installation SpaceElectricity and Safety Safety PrecautionsInstallation and Safety Drips, etc., oil, or smoke Operation and Safety GAS Before Using the Product Correct posture to use the product Preparations Checking the ContentsComponents Checking the ComponentsItems sold separately Frontal Buttons PartsPower Key Go to SETUP&RESET Power Key and select Power Off orPort Description Reverse SideConnect to the power cable Attaching the cradle InstallationRotating the Monitor Adjusting the Product Tilt and HeightInstalling a Wall-mount Kit or Desktop Stand Anti-theft Lock What is a PC over IP? Using PCoIPLAN Connection Connecting USB DevicesConnection to Use PCoIP Connecting a Serial cable Connecting a MicrophoneConnecting to Headphones or Speakers Connecting the Power Connecting to a Secondary MonitorConnect to the host PC using a LAN cable Installing a USB-to-Serial Driver Using PCoIP Connect Button PCoIPOn Screen Display OSD Connect ScreenOSD Options Menu Configuration WindowSubnet Mask Enable DhcpNetwork Tab IP AddressIPv6 Tab Secondary DNS Enable IPv6Enable DHCPv6 Link Local AddressLabel Tab Discovery Tab Enable DiscoveryAdvanced Session TabConnection Type DNS Name or IP AddressKeyboard Layout Language TabDisplay Tab Screen-Saver TimeoutOSD Tab Enable display override 11 Display ConfigurationEvent Log Tab Diagnostics WindowReset Tab † Clear Session Statistics TabView event log message † RefreshPCoIP Processor Tab 15PCoIP Processor Ping Tab Information Window† Firmware Version † MAC Address† Firmware Part Number † Hardware Version† Bootloader Build Date User Settings Window† Bootloader Version † Bootloader Build IDAllow the unverifiable connection VMware View TabReject the unverifiable connection Mouse Speed Mouse TabKeyboard Tab Keyboard Repeat DelayImage Quality Preference ImageDisplay Layout Display TopologyPosition ResolutionAlignment PrimaryTouch screen calibration Enable right click on holdRight click delay Touch Screen24Change Password Old Password Password Window25Authorized Password Reset Wake On LAN Wake on USB OSD Logo Upload Pre-connection Checkpoints Connecting and Using a Source DeviceBefore Connecting Connecting a Stereo Cable Connecting and Using a PCConnecting to a PC Connection Using the D-SUB Cable Analogue TypeWindows Driver Installation NC191 Setting Optimum ResolutionChanging the Resolution Using a PC Changing the Resolution on Windows Brightness Screen SetupConfiguring Brightness Contrast Configuring ContrastSharpness Configuring SharpnessSamsung Magic Bright Configuring Samsung Magic BrightCoarse Adjusting CoarseFine Adjusting FineSamsung Magic Color Configuring TintConfiguring Samsung Magic Color Red Configuring RedGreen Configuring GreenBlue Configuring BlueColor Tone Configuring the Color Tone SettingsGamma Configuring GammaPosition & V-Position Configuring H-Position & V-PositionResizing or Relocating the Screen Menu H-Position & Menu V-Position Configuring Menu H-Position & Menu V-PositionPress to configure Menu H-Position or Menu V-Position Initializing Settings Reset Setup and ResetReset Changing the Language LanguageDisplay Time Configuring Display TimeChanging Menu Transparency Menu TransparencyEnabling Power Key Power KeyDisplaying Information Configuring Volume in the Initial ScreenInformation Menu and Others Natural Color Installing the SoftwareWhat is Natural Color? MultiScreen Installing the SoftwareRestrictions and Problems with the Installation MultiScreen Removing the Software Check the following Troubleshooting GuideTesting the Product Checking the Resolution and FrequencySource device issue Not Optimum Mode is displayedQuestion Answer 10.2 Q & aTroubleshooting Guide General SpecificationsEnvironme Operating PowerSaver Standard Signal Mode Table 49.702 59.810 83.500 65.290 59.954 146.250 Contact Samsung World Wide AppendixEurope Denmark Asia Pacific India Africa Others Responsibility for the Pay Service Cost to CustomersProduct damage caused by customers fault Not a product defectCorrect disposal of batteries in this product Correct DisposalOSD On Screen Display TerminologyVertical Frequency Index Terminology What is a PC over IP?