Samsung SPN4235 manual Connecting Speakers, How to Connect

Page 12

Cable with a Cable Box that Descrambles Some (But Not All) Channels

To complete this connection you will need a two-way splitter, an RF (A/B) switch, and four coaxial cables (which you can buy from your Samsung dealer or any electronics store).

Find and disconnect the cable that is con-

1 nected to the ANTENNA IN terminal of your cable box.

This terminal might be labeled "ANT IN", "VHF IN", or simply, "IN". Connect this cable to a two-way splitter.

Connect a coaxial cable between an OUT-

2 PUT terminal of the splitter and the IN termi- nal of the cable box.

Connect a coaxial cable between the

3 ANTENNA OUT terminal of the cable box and the B-IN terminal of the A/B switch.

Connect a coaxial cable between the

4 ANTENNA OUT terminal of the cable box and the B-IN terminal of the A/B switch.

Connect the last coaxial cable between the

5 OUT terminal of the RF (A/B) switch and the VHF/UHF terminal on the PDP.

After you've made this connection, set the A/B switch to the "A" position for normal viewing.

Set the A/B switch to the "B" position to view scrambled channels. (When you set the A/B switch to "B", you will need to tune your Set-Top Box to the cable box's output channel, which is usually channel 3 or 4.)

22

Connecting Speakers

External speakers are sold seperately. Check with your dealer.

Speaker Audio Cablele

Powered Subwooper

(Option)

✱ External speakers MUST have a power handling capability of 10 watts minimum (impedance 8 ohm).

Please use the speaker-built in amplified audio.

How to Connect

Connect the speaker audio cable to the external speaker output jack on the PDP matching the “+” and “-” ends of the cable with the diagram on the PDP.

Connecting PDP and Speakers

1 Fix the bracket onto the guide pole located on the rear of speaker and fasten the screws.

2 After removing the three screws on the PDP, clamp the speaker and the PDP together and fasten the screws.

Guide pole

Guide pole

23

Image 12

Contents Owner’s Instructions Important Safety Information Thank You for Choosing SamsungFCC Information Table of Contents User InstructionsGeneral Information Your New Plasma Display Panel Remote Control Buttons Wall Installation Instructions Installation NotesWall attachment panel Insulation holders 4 EAHow to Adjust Mounting Angle Factory defaultChangeing the angle Connections Connecting VHF and UHF Antennas Connecting Cable TVAntennas with 75-ohm Round Leads Cable without a Cable BoxConnecting Speakers How to ConnectConnecting a VCR Connecting a CamcorderConnecting a VCR to the Video or S-Video/Audio jack Viewing camcorder tapesPlaying DVD Watching DTVTo Play DVD To Watch DTVOperation Turning the PDP On and Off Viewing the Menus and DisplaysViewing the Menus Displaying Status InformationSelecting the Video Signal-source Memorizing the ChannelsTo View Memorized Channel PIP Mode Setting Up Your Remote Control Adjusting the VolumeUsing Mute Changing ChannelsRemote Control Codes Picture ControlVCR Codes Cable Box Codes DVD Codes Using Automatic Picture Settings Customizing the PicturePress the Menu button, then press the Enter Button Press the Menu button to exitSelecting the Color Tone DNIe Digital Natural Image engineViewing the Picture-in-Picture Selecting the PIP ScreenPress the UP or Down button to select Source Changing the Size of the PIP Window Changing the Location of the PIP Image STD, HRD or IRCChanging the Screen Size Sound Control Customizing the Sound Using Automatic Sound Settings Volume Button to select Sound, then press the EnterPress the UP or Down button to select Auto Press the Left or Right button to select Mono Stereo or SAPUsing Dolby Virtual Using a SubwooferChannel Control Fine Tuning Channels LNA Low Noise AmplifierConnecting a PC and Operation Connecting to a PC Pin ConfigurationSetting up Your PDP Plug and Play To watch the PC screenHow to Set up Your PC Software Windows only 75.000 37.500Adjusting the PC Screen Adjusting the R.G.BCustom. When Custom is selected, the word Color Adjust will appear on the screenVertical, horizontal frequencies and resolution Changing the Size of the Image InformationTion, then press the Enter button AppearPicture Quality Adjustment Picture Automatic AdjustmentCoarse Adjustment Time Setting Fine Tuning FineRemove picture noise on the screen by pressing Setting the Clock Setting the Sleep Timer Button to select Function, then press the EnterPress the UP or Down button to select Sleep Setting the Timers Setting the On/Off TimerSetting the Preferred Channel and Volume Level Function DescriptionSelecting a Menu Language Viewing Closed Captions Setting Auto Power Off Power OffDigital Noise Reduction Using the V-Chip How to Enable/Disable the V-ChipHow to Set up Restrictions Using the TV guidelines Mpaa Rating Selecting the Film Mode AppendixTroubleshooting Care and Maintenance Specifications Memo