Samsung PS42P2SB, PS50P2HB manual Connecting Speakers

Page 13

Connecting Speakers

ENG

ConnectingPDPandSpeakers

Fix the bracket onto the guide pole located on the rear of speaker and fasten the screws. After removing the three screws on the PDP, clamp the speaker and the PDP together and fasten the screws.

Guide pole

Guide pole

ConnectingStandandSpeakers

		➢ When moving your PDP, do NOT hold the
		speaker connected to your PDP.
		It may damage the bracket clamping the
	Guide pole	speaker and your PDP together and
	Guide pole	result in a drop of your PDP and a risk of
		result in a drop of your PDP and a risk of
		personal damage and injury.

Rear of the Media Station

Connect the speakeraudiocabletotheexternalspeakeroutput jack on the rearoftheMediaStationmatchingthe“+”and“-”ends

of the cable with the diagram on the Media Station.

Rear of the PDP

➣◆ The speakers MUST have more than 15watts rating (impedance 8Ω).

◆The ferrite cores are used to attenuate undesired signals. When you connect the speaker wire to the EXTERNAL SPEAKER OUT (8Ω) connector, bind the speaker wire round the ferrite core to secure it.

13

Image 13

Contents Plasma Display with Media Station User Instructions Safety InstructionsChecking Parts Contents Contents Viewing the Plasma Display For further details, refer to Switching On and Off onPlug the mains lead into an appropriate For further details about connection, refer to pages 48~51 Viewing the Media StationPower Remote Control ButtonsInstalling the Display on the Wall Attachment Panel Inserting the Batteries in the Remote Control Degrees of tilt No tilt Been set to 5 degrees Been set to 15 degrees Been tiltedBolt Insulation rubber Remove four large screws from the rear side of the displaySeparating the Display from the Wall Attachment Panel Connecting Speakers Connecting to an Aerial or Cable Television Network Switching On and Off Button Viewing Function Menu Function Becoming Familiar with the Remote ControlMenu Setting up your Remote Control To start the store, press the joystick button Plug and PlayChoosing Your Language Lock the channels see Storing Channels AutomaticallySorting the Stored Channels Auto PAL Secam NTSC4.43 NTSC3.58 Storing Channels ManuallyD/K I M Channel mode LNA Editing the ChannelsFine Tuning Channel Reception To adjust the Contrast, Brightness, Sharpness, Colour, or Adjusting the Picture SettingsChanging the Picture Standard Custom Dynamic Standard Movie Custom High Middle LowFreezing the Current Picture Changing the Picture SizeStandard Full Normal Custom Colour l Colour 2 Colour Adjusting the Picture Settings PC or DVI ModePreset to the PC mode by using the Source button Setting the Picture PC ModeChanging the Sound Standard Adjusting the Sound SettingsCustom Standard Music Movie Speech Adjusting the Volume Automatically Selecting the Sound Mode Off Virtual Pro Logic Setting the Dolby SurroundNormal Phantom Wide Virtual OffNormal PhantomAdjusting the Dolby Pro Logic Preferences Volume, Bass, Treble, Balance Adjusting the Headphone PreferencesAdjust the each option Up or down Setting the Current TimeHearing the Melody Sound Move the joystickSwitching On and Off Automatically Press the Sleep button on the remote control Setting the Sleep TimerTV AV 1 AV 2 AV 3 AV 4 AV Viewing the Picture in Picture PIPLarge Small Double 1 Double Listening to the Sound of the Sub Picture Front panel Viewing Pictures From External SourcesContents Teletext FeatureDisplaying the Teletext Information To display Press Selecting Display OptionsSecondary page by entering its number Time/SubcodeSelecting a Teletext Input Connecting to the S-Video Input Connecting to the DVD InputConnecting to the DVI Input Connecting to the Audio OutputPreset Signals Connecting to the PC InputFrequency Horizontal frequency Resolution Source Video1024 x 768 pixels Setting up Your PC Software Windows onlyStandard Dot x Line Vertical Horizontal Input Mode PC/DVIPinSignal Pin ConfigurationsPin Care and Maintenance TroubleshootingAfter Sales Service