Samsung PS50P2HB, PS42P2SB manual Safety Instructions, User Instructions

Page 2

Safety Instructions

ENG

◆Do not place the PDP on an unstable cart, stand, tripod, bracket, table, or floor where it can fall.

◆Do not expose the PDP to extreme temperature conditions or to extreme humidity conditions.

◆Do not expose the PDP to direct sunlight and other sources of heat.

◆Do not expose the PDP to any liquids.

◆Never put objects of any kind into the television, and do not place a water-containing vessel on the PDP.

◆During a storm conditions (especially when there is lightning) unplug the PDP from the mains socket and aerial.

◆Do not step on or twist the power cord.

◆Do not overload wall outlets or extension cords as this can result in a risk of fire or electric shock.

◆Please use a soft and dry cloth (not containing volatile matter) when you clean the PDP.

◆If the PDP is broken, do not try to repair it yourself. Contact qualified service personnel.

◆If the remote control is not used for a long period of time, remove the batteries and store it in a cool, dry place.

◆Do not drop the remote control.

User Instructions

◆Screen Image retention

Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the plasma monitor panel for more than 2 hours as it can cause screen image retention. This image retention is also known as “screen burn”. To avoid such image retention, reduce the degree of brightness and contrast of this screen when displaying a still image.

◆Cell Defect

The plasma display panel consists of fine cells. Although the panels are produced with more than 99.9 percent active cells, there may be some cells that do not produce light or remain lit.

◆Height

The PDP can normally operate only under 2000m in height. It might abnormally function at a place over 2000m in height and do not install and operate there.

◆Warranty

- Warranty Period: One year starting from the purchase of your PDP. - Warranty does not cover any damage caused by image retention.

- Burn-in is not covered by the warranty.

2

Image 2

Contents Plasma Display with Media Station Safety Instructions User InstructionsChecking Parts Contents Contents Plug the mains lead into an appropriate For further details, refer to Switching On and Off onViewing the Plasma Display Viewing the Media Station For further details about connection, refer to pages 48~51Remote Control Buttons PowerInserting the Batteries in the Remote Control Installing the Display on the Wall Attachment PanelBeen set to 5 degrees Been set to 15 degrees Been tilted Degrees of tilt No tiltRemove four large screws from the rear side of the display Bolt Insulation rubberSeparating the Display from the Wall Attachment Panel Connecting Speakers Connecting to an Aerial or Cable Television Network Switching On and Off Menu Becoming Familiar with the Remote ControlButton Viewing Function Menu Function Setting up your Remote Control Plug and Play To start the store, press the joystick buttonChoosing Your Language Storing Channels Automatically Lock the channels seeSorting the Stored Channels D/K I M Storing Channels ManuallyAuto PAL Secam NTSC4.43 NTSC3.58 Channel mode Editing the Channels LNAFine Tuning Channel Reception Changing the Picture Standard Adjusting the Picture SettingsTo adjust the Contrast, Brightness, Sharpness, Colour, or Custom Dynamic Standard Movie Custom High Middle LowStandard Full Normal Changing the Picture SizeFreezing the Current Picture Adjusting the Picture Settings PC or DVI Mode Custom Colour l Colour 2 ColourSetting the Picture PC Mode Preset to the PC mode by using the Source buttonCustom Standard Music Movie Speech Adjusting the Sound SettingsChanging the Sound Standard Adjusting the Volume Automatically Selecting the Sound Mode Normal Phantom Wide Setting the Dolby SurroundOff Virtual Pro Logic Normal OffVirtual PhantomAdjusting the Dolby Pro Logic Preferences Adjusting the Headphone Preferences Volume, Bass, Treble, BalanceHearing the Melody Sound Setting the Current TimeAdjust the each option Up or down Move the joystickSwitching On and Off Automatically Setting the Sleep Timer Press the Sleep button on the remote controlViewing the Picture in Picture PIP TV AV 1 AV 2 AV 3 AV 4 AVLarge Small Double 1 Double Listening to the Sound of the Sub Picture Viewing Pictures From External Sources Front panelTeletext Feature ContentsDisplaying the Teletext Information Secondary page by entering its number Selecting Display OptionsTo display Press Time/SubcodeSelecting a Teletext Input Connecting to the DVD Input Connecting to the S-Video InputConnecting to the Audio Output Connecting to the DVI InputFrequency Horizontal frequency Resolution Connecting to the PC InputPreset Signals Source VideoSetting up Your PC Software Windows only 1024 x 768 pixelsInput Mode PC/DVI Standard Dot x Line Vertical HorizontalPin Pin ConfigurationsPinSignal Troubleshooting Care and MaintenanceAfter Sales Service