Samsung PS-37S4A manual User Instructions

Page 2

User Instructions

ENG

Screen Image retention

Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the plasma monitor panel for more than 2 hours as it can cause screen image retention. This image retention is also known as “screen burn”. To avoid such image retention, reduce the degree of brightness and contrast of this screen when displaying a still image.

Cell Defect

The plasma display panel consists of fine cells. Although the panels are produced with more than 99.9 percent active cells, there may be some cells that do not produce light or remain lit.

Height

The PDP can normally operate only under 2000m in height. It might abnormally function at a place over 2000m in height and do not install and operate there.

Heat

PDP TV displays picture by Plasma discharge. For this reason, using the PDP TV for a long period of time results in dissipation of heat by the panel.

Please note that the top side of the product may be hot after use for long periods of time as the heat dissipation from the panel through the vent hole in the upper part of the product.

You don't have to worry since PDP TV’s heat dissipation does not necessarily indicate any defect or operation failure of the product.

Particularly when watching TV with children, adults should prevent children from touching the upper part of the product.

Warranty

- Warranty does not cover any damage caused by image retention. - Burn-in is not covered by the warranty.

2

Image 2
Contents PDP-TELEVISION User Instructions Scart Cable Sold SeparatelyVideo Cable Contents Symbols ContentsDepending on your model Actual configuration on your PDP may be differentYour New Plasma Display Panel Rear Panel For further details about connection, refer to pages 55~59Infrared Remote Control Inserting the Batteries in the Remote Control Assembling the Stand-BaseInstalling the Display on the Wall Attachment Panel Wall Mount Bracket Plastic HangerWall Using a Coaxial cable Connecting to an Aerial or Cable Television NetworkConnecting a Satellite Receiver or Decoder Rear of the PDPMains lead is attached to the rear of your PDP Switching On and OffPlacing in Standby Mode Front of the PDPChange channels and adjust the volume Becoming Familiar with the Remote ControlRemote control is used mainly to Display the on-screen menu systemSetting Up Your Remote Control Plug & Play Feature To start the search, press the Enter buttonIf you want to reset this feature Choosing Your LanguageStoring Channels Automatically SeeAuto PAL Secam or Storing ChannelsManuallyYou wish to identify Auto NT3.58 NT4.43 PAL60Channel mode Result The Edit menu is displayed Skipping Unwanted ChannelsSkipping unwanted channels Sorting the Stored Channels Assigning Names to Channels Using the LNA Low Noise Amplifier Feature Result The options available are listedActivating the Child Lock Activating the child lockDynamic Standard Movie Custom High Middle Low Custom Displaying InformationChanging the Picture Standard Colour Tone Cool2, Cool1, Normal, Warm1, Warm2 Adjusting the Picture SettingsBrightness, Sharpness Adjusting the Picture Settings PC or DVI Mode Custom PC mode only Colour1 Colour2 Colour3Setting the Picture PC Mode Preset to the PC mode by using the Source buttonSetting the Picture PC Mode If reception is weak, you can fine tune a channel manually Using the Fine TuneColour System and Sound System settings are correct Result Main menu is displayed Viewing the Channel Scan PictureFreezing the Current Picture Result You can view every memorized channel in orderSelecting the Picture Size Positioning and Sizing the screen using ZoomPC to DVI Mode Selecting the Film Mode DNIeTM Digital Natural Image engineSetting the Blue Screen Setting the Melody SoundResult The sources are displayed in the following order Table of PIP SettingsViewing the Picture In Picture PIP TV Ext.1 Ext.2 Ext.3 AV1 AV2Component2, PC, DVI Easy functions of remote controlExt.2, Ext.3, AV1, AV2, S-Video,Component1 Using the Digital NR Digital Noise Reduction Feature Changing the Sound Standard Standard Music Movie Speech CustomAdjusting the Sound Settings Adjusting the Volume AutomaticallyStereo Setting the TruSurround XTSelecting the Internal Mute Selecting the Sound Mode depending on the model Setting the Sleep Timer Setting and Displaying the Current Time Switching the Television On and Off Automatically Absent Power OffViewing an External Signal Source Satellite STB, AV Receiver, DVD Receiver, GameRedirecting an Input to the External Output Teletext Feature ContentsDisplaying the Teletext Information Press the TTX/MIX button againSelecting Display Options To display PressSelecting a Teletext TeleWeb Feature Option Entering the bookmarked URL Using the TeleWeb Menu after Displaying the TeleWebBookmarking the current Opening the HomeEasy Accessing the TeleWeb Service via the Remote Control Button Function TeleWebRear of the TV Connecting to the External DevicesInput/Output Specification InputConnecting to the S-Video Input Rear of the TVConnecting to the DVI Input Connecting to the PC InputConnecting to the Component Input To Display the DVD Home Theater Connecting and Using the Home Theater SystemConnecting the Home Theater System Shown at left is a typical screen for Display dialog box Setting up Your PC Software Windows onlyBit colour NVidia chipset Input Mode PC/DVIVideo Signal Dot x Line Vertical Horizontal Pin Configurations Check the volume Power buttonCheck the picture contrast and brightness settings Normal picture but no sound Check the volume019, 023 Programming the Remote Control for Other Components003, 024 Wamer amex040, 047, 050, 052, 060, 063, 065, 066, 067 Programming the Remote Control for Other ComponentsBell&Howell After Sales Service