Toshiba 51H93 owner manual Setting the time and date, To set the time and date

Page 51

Chapter 6: Setting up your TV

Adjusting the color convergence

(continued)

RED BLUE

: TO ADJUST

ENTER : TO SELECT COLOR

EX I T : TO SELECT POSITION

8.Press ENTER to highlight RED or BLUE, depending on which color needs adjusting. If both red and blue need adjusting, you will need to perform steps 8 and 9 twice for the selected area.

9.Press yzx • to converge the red or blue line into the white line. Repeat steps 8 and 9 until you see two single crossed white lines.

10.Press EXIT once to select another area to adjust, and then repeat steps 7–9.

11.Press EXIT a second time to close the Convergence menu.

Setting the time and date

Note: If you already set up the TV Guide On Screen system, the time and date were set automatically and you can skip this step.

To set the time and date:

1.Press MENU and open the SETUP menu.

2.Highlight INSTALLATION and press ENTER. (A new set of INSTALLATION menu icons will appear on-screen, as shown in step 3 below.)

Setup

Installation

Sleep Timer

On/Off Timer

Digital Tuner Hold • • • • • • • Off

Slide Show Interval • • • 2 Sec

Convergence

3.Open the TIME AND DATE menu, highlight START SETUP, and press ENTER.

Time and Date

Start Setup

If you have not set up the TV Guide On Screen system, the following screen will appear. To set the time, highlight TV GUIDE and press ENTER. The TV Guide On Screen setup sequence will start, and the time and date will be set automatically.

Time and Date

Your TV Guide On Screen system can provide

accurate time and date information.

It is recommended you set up TV Guide On Screen

first, and use it to obtain the time and date.

Manual

TV Guide

Cancel

Note: If you do not set up the TV Guide On Screen system and you manually set the time and date (by highlighting MANUAL instead of TV GUIDE, above), you will lose the time and date information if a power outage occurs. If you set the time and date through the TV Guide On Screen system and a power outage occurs, the time and date will be automatically updated when the power is restored.

Copyright © 2003 TOSHIBA CORPORATION. All rights reserved.	51

Image 51

Contents 51H93 57H93 65H93 Tune Into Safety Safety PrecautionsIt Makes a Difference Where Your TV Stands IssueImportant Safety Instructions Installation, Care, and ServiceAlways place the TV on the floor TV, follow these recommendations and precautions When the unit is being turned on orOr continuous, unplug the power cord Contact a Toshiba Authorized Service CenterContents Contents from previous Introduction Features of your new TVInstalling, setting up Using your newDemo TV back panelConnecting your TV TV front panel controls and connections4 5 6 7 8 For an explanation of cable types, see TV back panel connectionsOverview of cable types From Cable TV or antenna You will needTwo coaxial cables To view the VCRSelect the Video 1 video input source Connecting a VCR and Cable boxVCR’s audio out jack using the white audio cable only To view basic and premium Cable channelsTo view the VCR or view and record antenna channels Connecting a VCR and satellite receiverTo view the DVD player Connecting a DVD player with S-video and a VCRTo view basic channels and access the TV’s features To view premium Cable channelsTo record a TV program while watching a DVD Connecting a DVD player with component video and a VCROne set of component video cables Source on the TVYou will need One set of standard A/V cables Connecting two VCRsConnecting a VCR to the REC OUT jacks To view VCRSelect the Video 3 video input source Connecting a DVI/HDCP deviceConnecting a camcorder To view the camcorder videoOne optical audio cable Connecting a digital audio systemConnecting an analog audio system Highlight Audio Setup and press EnterConnecting an A/V receiver Dolby Pro Logic surround soundSystem connection example To control the devices Are on-screen. To access other deviceTheaterNet on-screen device control To connect the IR blaster cableUsing TheaterNet on-screen device control Connecting IEEE-1394 Firewire video devicesUsing analog-compatible IEEE-1394 devices Supported signalsIEEE-1394 device initialization IEEE-1394 device managementTo edit the IEEE-1394 device information Hub connection IEEE-1394 device interconnectionChain connection Hub connectionLink connection To connect to the G-LINK jackSee Using the remote control Learning about the remote controlChannel Numbers 0-9, 100 directly access channels Installing the remote control batteries To install the remote control batteriesDevice mode control after programming Remote Control functional key chart CBL/SAT Audio VCR CH RTN Searching and sampling the code of a device Device code setupPress Mode to select the TV mode to control the TV Press Mode to select the mode you want to set upTo reset the volume controls to the original device mode Using the volume lock featureOperational feature reset Repeatedly press Mode to select CABLE/SAT modeMulti-brand remote control device codes VCRsCable boxes Laser disks CD playersReceivers Cassette playersMain menu layout Menu layout and navigationTo close a menu instantly, press Exit Setup / Installation menu layoutNavigating the menu system Press Menu to open the menu systemSelecting the menu language Starting the Quick Connect Guide assisted setupManually starting the Quick Connect Guide assisted setup If you already set up the TV Guide On Screen system, go toFollowing screen opens. Press Enter to continue Setting up the TV Guide On Screen systemConfiguring the location of your TV Configuring your Cable setupFor G-LINK connection details, see Cable box code testingConfiguring your VCR setup Do you have a VCR? Select YES or NO, and then pressVCR code testing Confirming your settingsSee ÒImportant final setup steps,Ó next Important final setup steps Completing the Quick Connect Guide assisted setupSelecting the menu language Setting up your TVConfiguring the antenna input sources To configure the ANT 1 and ANT 2 input sourcesProgramming channels into the TV’s channel memory Programming channels automaticallyTo program channels automatically Manually adding and deleting channels in the channel memory To add and delete channels in the Favorite Channels lists To clear your favorite channel listsTo tune your favorite channels To remove a device from TheaterNet Setting up and using TheaterNet on-screen device controlSetting up TheaterNet To set up TheaterNet device controlTo view another source Using the TheaterNet control iconsTo close the on-screen control icons Press ExitMiscellaneous audio devices TheaterNet IR device codesAmplifiers Laser disk playersADC Video accessory Hdtv decoder ReceiversSTS Convergence using TouchFocus Adjusting the color convergenceManually adjusting the color Automatically adjusting the colorTo set the time and date Setting the time and dateChecking system status Viewing the digital signal meterSkip these steps and go to the next TV Guide On Screen system includes the following featuresAction buttons About the TV Guide On Screen menu screensPanel ad Channel Blue and Green WindowsNavigating the TV Guide On Screen system Channel surfing Listings menuViewing program listings and descriptions Info windowsOne-touch and VCR Plus+ recording Direct tuningSetting programs as favorites Video WindowTo open the Sort menu Using the Menu Bar to access other menusSort menu Viewing panel ads and channel adsSchedule menu Setup menuChange system settings Review options change the auto display settingTroubleshooting Promotions menuMessages menu Using the TV’s features Using the digital tuner holdSelecting the video input source to view To label the video input sources To clear the video labels Labeling the video input sourcesUsing SpeedSurf to change to a specific programmed channel Tuning channelsTuning to the next programmed channel Switching between two channels using Channel ReturnTo select the picture size Press PIC Size on the remote controlSelecting the picture size Natural picture sizeFull picture size Theater Wide 1 picture sizeTheater Wide 2 picture size Theater Wide 3 picture sizeUsing the auto aspect ratio feature 480i signals only To turn on the Auto Aspect featureTo turn off the Auto Aspect feature To select the display format Selecting the cinema modeTo set the Cinema Mode to Film To set the Cinema Mode to VideoTo close the POP window Using the POP featuresUsing the POP double-window feature To display a program in the POP windowTo close the still POP window Switching the main and POP picturesAdjusting the size of the main and POP pictures Freezing the main picture in the POP double-windowTo scan the programmed channels Using the programmed channel scan featureTo cancel the channel scan without changing the channel POP double-window aspect ratioUsing the favorite channel search feature To scan and tune your favorite channelsDigital channels will not display in the POP multi-windows Resetting the picture settings Adjusting the pictureSelecting the picture mode Adjusting the picture qualityTo turn on the flesh tone feature To activate the ALSTo deactivate the ALS Using CableClear DNR digital noise reduction Selecting the color temperatureResetting the advanced picture settings Advanced closed captions Using the closed caption modeTo listen to stereo sound Adjusting the audioMuting the sound Selecting stereo/SAP broadcastsUsing the sub-bass system SBS Adjusting the audio qualityUsing the StableSound feature Using the SRS WOW surround sound featureResetting your audio adjustments Turning off the built-in speakers Selecting the Audio OUT soundSelecting the optical audio output format Using Memory card picture viewer Memory card specificationsViewing digital photos on your TV To close the picture viewer Using the memory card picture viewerMemory card care and handling To set the slide show intervalSetting the sleep timer Setting the ON/OFF timerUnderstanding the last mode memory feature Displaying TV setting information on-screenViewing the demo mode Understanding the auto power off featureChanging your PIN code Using the Locks menuEntering the PIN code If you cannot remember your PIN codeEdit Rating Limits screen below appears Blocking TV programs and movies by rating V-ChipTo block and unblock TV programs and movies Press z to highlight Edit Rating Limits and pressBlocking channels Unlocking programs temporarilyLocking video inputs Using the front panel lock feature Using the game timerTroubleshooting Closed caption problems If Audio OUT is set to POP in the Audio Setup menuSound may be muted. Press Volume Set to SAP modeSetup Questions TV Guide On Screen FAQsOperational Questions Why won’t my VCR turn on?How do I resize or close the Info window? Edid = Enhanced-Extended Display Identification AppendixFor 27 FST Pure and All Larger Television Models Limited United States WarrantyHow to Obtain Warranty Services Limited Canada WarrantyCopyright 2003 Toshiba CORPORATION. All rights reserved Copyright 2003 Toshiba CORPORATION. All rights reserved Picture-out-picture POP Picture adjustmentsIndex Channel programmingOn/off Remote control03-07 R 23565982 Manufactured by